| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Certain HP Smart Tank All-in-One printers may be potentially vulnerable to a denial of service condition that allows an unauthenticated attacker to cause the device to become unavailable by sending multiple concurrent HTTP requests. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to obtain sensitive information due to a buffer overflow. |
| Zephyr's 6LoWPAN IP Header Compression (IPHC) uncompression code contains an out-of-bounds read in get_ihpc_inlined_size() (subsys/net/ip/6lo.c). The destination inline size is looked up in da_inline_size_table, which has 13 entries, using an index built from the M, DAC and DAM bits of the received IPHC dispatch word (iphc & NET_6LO_IPHC_DA_MASK, a 4-bit value of 0-15). The reserved combinations 13, 14 and 15 are not bounds-checked and read past the end of the table.
The iphc word is taken directly from the received frame, and get_ihpc_inlined_size() is reached on every inbound 6LoWPAN frame via net_6lo_uncompress() from the 802.15.4 receive path (subsys/net/l2/ieee802154/ieee802154_6lo.c and ieee802154_6lo_fragment.c). An unauthenticated attacker on the radio/adjacent link can therefore craft a frame whose destination addressing-mode nibble selects an out-of-range index, with no privileges or user interaction.
The out-of-bounds value becomes the computed inline_size, which then drives header reconstruction before the buffer-length check: it is used to dereference *(pkt->buffer->data + sizeof(iphc) + inline_size) and to compute a size_t diff that can underflow, leading to a further out-of-bounds read of the packet buffer and malformed uncompression. The practical impact is a radio-triggerable out-of-bounds read / denial-of-service on the receiver; the leaked byte is not returned to the attacker. The fix rejects any destination index beyond the table, aborting processing of the malformed frame. |
| The WNC-M14A2A LTE-M modem driver mishandles unsolicited %NOTIFYEV: events in on_cmd_socknotifyev() (drivers/modem/vendor_standalone/wncm14a2a.c). The response line is linearized into a fixed 40-byte stack buffer via net_buf_linearize(), which caps the copy at 39 bytes and returns out_len <= 39. The two quote-delimiter scanning loops, however, were bounded by len — the full CR/LF-delimited frame length returned by net_buf_findcrlf() — rather than by out_len.
When a %NOTIFYEV: line longer than 39 bytes contains no " within the linearized region, the loop indices p1/p2 walk past value[39] and read adjacent stack memory until a stray quote byte is found or the index reaches len. The over-read string is then passed to strncmp()/atoi()/LOG_*, and if a quote byte is found out of bounds the subsequent value[p2] = '\0' performs a single-NUL out-of-bounds stack write at an attacker-influenced offset.
The %NOTIFYEV: payload carries network-derived content (LTIME network time, SIB1 base-station system information, CSPS/RRCSTATE), so a rogue cellular base station, a malicious or compromised modem module, or RF manipulation that induces an over-long notify line reaches the defect without any application interaction; the handler runs automatically on the unsolicited event in the modem RX thread.
The impact is out-of-bounds stack disclosure (into logs and parsing) and stack corruption that can crash the modem RX thread (denial of service). The write offset is only weakly controlled, so memory-safe code execution is not demonstrated. The fix bounds both scanning loops by out_len, keeping all accesses within the linearized buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix use-after-free in amdxdna_gem_dmabuf_mmap()
When vm_insert_pages() fails, the error path calls vma->vm_ops->close(vma)
which internally calls drm_gem_vm_close() → drm_gem_object_put(),
releasing the GEM object reference acquired at the start of the function.
However, the close_vma label then falls through to put_obj, which calls
drm_gem_object_put() a second time on the same object.
If the first put releases the last reference, the object is freed and the
second put accesses freed memory, causing a use-after-free.
Fix by returning directly from close_vma instead of falling through to
put_obj, since the close handler already performs all necessary cleanup
including the object put. |
| In the Linux kernel, the following vulnerability has been resolved:
openrisc: Fix jump_label smp syncing
The original commit 8c30b0018f9d ("openrisc: Add jump label support")
copies from arm64 and does not properly consider how icache invalidation
on remote cores works in OpenRISC. On OpenRISC remote icaches need to
be invalidated otherwise static key's may remain state after updating.
Fix SMP cache syncing by:
1. Properly invalidate remote core icaches on SMP systems by using
icache_all_inv. The old code uses kick_all_cpus_sync() which runs a
no-op IPI function call on remote CPU's which does execute a lot of
code and flushes many cache lines in the process, but does not flush
all and it's not correct on OpenRISC.
2. For architectures that do not have WRITETHROUGH caches be sure
to flush the dcache after patching.
To test this I first reproduced the issue using a custom test module
[0]. The test confirmed that some icache lines maintained stale
static_key code sequences after calling static_branch_enable(). After
this patch there are no longer jump_label coherency issues.
[0] https://github.com/stffrdhrn/or1k-utils/tree/master/tests/smp_static_key_test |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: bound copy_lcns dp->page_lcns[] index in analysis pass
In log_replay()'s analysis pass, after find_dp() returns a
valid DIR_PAGE_ENTRY for the (target_attr, target_vcn) tuple,
the copy_lcns block walks lrh->lcns_follow further entries:
t16 = le16_to_cpu(lrh->lcns_follow);
for (i = 0; i < t16; i++) {
size_t j = (size_t)(le64_to_cpu(lrh->target_vcn) -
le64_to_cpu(dp->vcn));
dp->page_lcns[j + i] = lrh->page_lcns[i];
}
find_dp() only validates that target_vcn falls within
[dp->vcn, dp->vcn + dp->lcns_follow), i.e., that the FIRST
cluster is covered. The walk through the further entries is
not bounded against dp->lcns_follow. For a malformed LRH
where target_vcn = dp->vcn + dp->lcns_follow - 1 and
lrh->lcns_follow > 1, the i > 0 writes overflow the dp's
allocated page_lcns[] array.
Add the missing j + lrh->lcns_follow <= dp->lcns_follow guard.
Reproduced under UML+KASAN on mainline 8d90b09e6741 as a
slab-out-of-bounds write of size 8 from log_replay+0x68d4 on
the mount path.
This is distinct from Pavitra Jha's 2026-05-02 patch
("fs/ntfs3: validate lcns_follow in log_replay conversion",
<20260502154252.164586-1-jhapavitra98@gmail.com>) which
addresses the separate version-0 dirty-page-table conversion
path's memmove(&dp->vcn, ...) call. The two fixes are
complementary; both should land.
[almaz.alexandrovich@paragon-software.com: clang-formatted the changes,
fixed conflicts] |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: validate index entries on reading
Validate index entries immediately after reading an index root or index
block from disk. This eliminates repeated checks in lookup and readdir,
and reduce the risk of missing checks in those paths. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: avoid heap allocation for free-cluster readahead state
get_nr_free_clusters() allocates a temporary file_ra_state before it
publishes the precomputed free cluster count, sets NVolFreeClusterKnown(),
and wakes vol->free_waitq. If that allocation fails, the worker returns
without setting the flag or waking waiters, so callers waiting for the free
count can block indefinitely.
The readahead state is only used synchronously while scanning the bitmap.
Keep it on the stack and pass it by address to the readahead helper. This
eliminates the early allocation failure path instead of adding a special
case that publishes a conservative count and wakes the waitqueue.
Zero-initialize the on-stack state because file_ra_state_init() only sets
ra_pages and prev_pos.
Apply the same treatment to __get_nr_free_mft_records(), which scans the
MFT bitmap with the same short-lived readahead state. |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: fix integer underflow in jbd2_journal_initialize_fast_commit()
jbd2_journal_initialize_fast_commit() validates journal capacity by
checking (journal->j_last - num_fc_blks < JBD2_MIN_JOURNAL_BLOCKS).
Both j_last and num_fc_blks are unsigned, so when num_fc_blks exceeds
j_last the subtraction wraps to a large value, bypassing the bounds
check.
The resulting underflow corrupts j_last, j_fc_first, and j_free,
leading to journal abort.
Fix by checking num_fc_blks against j_last before the subtraction,
returning -EFSCORRUPTED. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: prevent TVLV OOB check overflow
A TT unicast TVLV contains the number of VLANs stored in it. This number is
an u16 and gets multiplied by the size of the struct
batadv_tvlv_tt_vlan_data (8 bytes). The size can therefore overflow the u16
used to store the tt_vlan_len. All additional safety checks to prevent
out-of-bounds access of the TVLV buffer are invalid due to this overflow.
Using size_t prevents this overflow and ensures that the safety checks
compare against the actual buffer requirements. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: access unicast_ttvn skb->data only after skb realloc
The pskb_may_pull() called by batadv_get_vid() could reallocate the buffer
behind the skb. Variables which were pointing to the old buffer need to be
reassigned to avoid an use-after-free.
This was done correctly for the ethernet header but missed for the
unicast_packet pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: retrieve ethhdr after potential skb realloc on RX
pskb_may_pull() in batadv_interface_rx() could reallocate the buffer behind
the skb. Variables which were pointing to the old buffer need to be
reassigned to avoid an use-after-free.
This was done correctly for the VLAN header but missed for the ethernet
header which is later used for the TT and AP isolation handling. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix barriering when walking subrequest list
Fix the barriering used when walking the subrequest list in retry as
there's a possibility of seeing a subreq that's just been added by the
application thread. |
| In the Linux kernel, the following vulnerability has been resolved:
cachefiles: Fix double unlock in nomem_d_alloc error path
When start_creating() fails and returns -ENOMEM, it has already
released the parent directory lock in __start_dirop():
static struct dentry *__start_dirop(...)
{
...
inode_lock_nested(dir, I_MUTEX_PARENT);
dentry = lookup_one_qstr_excl(name, parent, lookup_flags);
if (IS_ERR(dentry))
inode_unlock(dir); <-- Lock released on error
return dentry;
}
However, the nomem_d_alloc error path in cachefiles_get_directory()
unconditionally calls inode_unlock(d_inode(dir)) again, causing a
double unlock that corrupts the rwsem state.
This is a leftover from commit 7ab96df840e60 which replaced manual
locking with start_creating() but failed to update the nomem_d_alloc
path (while correctly updating mkdir_error and lookup_error paths). |
| In the Linux kernel, the following vulnerability has been resolved:
afs: Fix the volume AFS_VOLUME_RM_TREE is set on
Fix afs_insert_volume_into_cell() to set AFS_VOLUME_RM_TREE on the volume
replaced, not the new volume, as it's now removed from the cell's volume
tree. This will cause the old volume to be removed from the tree twice and
the new volume never to be removed. |
| In the Linux kernel, the following vulnerability has been resolved:
afs: Fix reinitialisation of the inode, in particular ->lock_work
It seems that initalising afs_vnode::lock_work a single time in the slab's
init function isn't sufficient for work_structs. This results in the
DEBUG_OBJECTS debugging stuff producing a warning occasionally when running
the generic/131 xfstest:
ODEBUG: activate not available (active state 0) object: 0000000016d8760f object type: work_struct hint: afs_lock_work+0x0/0x220
WARNING: lib/debugobjects.c:629 at debug_print_object+0x4b/0x90, CPU#3: locktest/7695
...
CPU: 3 UID: 0 PID: 7695 Comm: locktest Tainted: G S 7.1.0-build3+ #2771 PREEMPT
...
RIP: 0010:debug_print_object+0x65/0x90
...
Call Trace:
<TASK>
? __pfx_afs_lock_work+0x10/0x10
debug_object_activate+0x122/0x170
insert_work+0x25/0x60
__queue_work+0x2e0/0x340
queue_delayed_work_on+0x48/0x70
afs_fl_release_private+0x57/0x70
locks_release_private+0x5c/0xa0
locks_free_lock+0xe/0x20
posix_lock_inode+0x55f/0x5b0
locks_lock_inode_wait+0x81/0x140
? file_write_and_wait_range+0x50/0x70
afs_lock+0xcd/0x110
fcntl_setlk+0x10d/0x260
do_fcntl+0x24e/0x5b0
__do_sys_fcntl+0x6a/0x90
do_syscall_64+0x11e/0x310
entry_SYSCALL_64_after_hwframe+0x71/0x79
Fix this by reinitialising ->lock_work after allocating an inode.
Also, flush ->lock_work when the inode is being evicted to make sure it's
not still running. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_teql: Introduce slaves_lock to avoid race condition and UAF
The teql master->slaves singly linked list is not protected against
multiple writes. It can be mod'ed concurently from teql_master_xmit(),
teql_dequeue(), teql_init() and teql_destroy() without holding any list
lock or RCU protection.
zdi-disclosures@trendmicro.com has demonstrated that the qdisc is freed
after an RCU grace period, but teql_master_xmit() running on another
CPU can still hold a stale pointer into the list, resulting in a
slab-use-after-free:
BUG: KASAN: slab-use-after-free in teql_master_xmit+0xf0f/0x16b0
Read of size 8 at addr ffff888013fb0440 by task poc/332
Freed 512-byte region [ffff888013fb0400, ffff888013fb0600) (kmalloc-512)
The fix?
Add a per-master slaves_lock spinlock that serializes all mutations of
master->slaves and the NEXT_SLAVE() links in teql_destroy() and
teql_qdisc_init(). teql_master_xmit() also takes the same slaves_lock
around those updates.
Annotate master->slaves and the per-slave ->next pointer with __rcu and
use the appropriate RCU accessors everywhere they are touched:
rcu_assign_pointer() on the writer side (under slaves_lock),
rcu_dereference_protected() for the writer-side loads (also under
slaves_lock), rcu_dereference_bh() for the loads in teql_master_xmit() and
rtnl_dereference() for the loads in teql_master_open()/teql_master_mtu(),
which run under RTNL.
Pair this with rcu_read_lock_bh()/rcu_read_unlock_bh() around the list
traversal in teql_master_xmit(), so that readers either observe a fully
linked list or are deferred until the in-flight mutation completes. The two
early-return paths in teql_master_xmit() are updated to release the RCU-bh
read-side critical section before returning, since leaving it held would
disable BH on that CPU for good. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: Validate iph->ihl in nf_flow_ip4_tunnel_proto()
Add sanity check for iph->ihl field in nf_flow_ip4_tunnel_proto() before
using it to compute the header size, avoiding out-of-bounds access with
malformed IP headers.
While at it, use iph->protocol instead of the hardcoded IPPROTO_IPIP
constant when setting ctx->tun.proto and reference ctx->tun.hdr_size
when updating ctx->offset. |
| Datasets through 5.0.0, fixed in commit f989ef9, contains a path traversal vulnerability in folder-based dataset builders where the file_name metadata field is not properly validated before being joined to the dataset directory. Attackers can supply crafted file_name values with directory traversal sequences to read arbitrary local files, which are then embedded into output when save_to_disk or push_to_hub is called. |
