| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: authencesn - reject short ahash digests during instance creation
authencesn requires either a zero authsize or an authsize of at least
4 bytes because the ESN encrypt/decrypt paths always move 4 bytes of
high-order sequence number data at the end of the authenticated data.
While crypto_authenc_esn_setauthsize() already rejects explicit
non-zero authsizes in the range 1..3, crypto_authenc_esn_create()
still copied auth->digestsize into inst->alg.maxauthsize without
validating it. The AEAD core then initialized the tfm's default
authsize from that value.
As a result, selecting an ahash with digest size 1..3, such as
cbcmac(cipher_null), exposed authencesn instances whose default
authsize was invalid even though setauthsize() would have rejected the
same value. AF_ALG could then trigger the ESN tail handling with a
too-short tag and hit an out-of-bounds access.
Reject authencesn instances whose ahash digest size is in the invalid
non-zero range 1..3 so that no tfm can inherit an unsupported default
authsize. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ks8851: Reinstate disabling of BHs around IRQ handler
If the driver executes ks8851_irq() AND a TX packet has been sent, then
the driver enables TX queue via netif_wake_queue() which schedules TX
softirq to queue packets for this device.
If CONFIG_PREEMPT_RT=y is set AND a packet has also been received by
the MAC, then ks8851_rx_pkts() calls netdev_alloc_skb_ip_align() to
allocate SKBs for the received packets. If netdev_alloc_skb_ip_align()
is called with BH enabled, then local_bh_enable() at the end of
netdev_alloc_skb_ip_align() will trigger the pending softirq processing,
which may ultimately call the .xmit callback ks8851_start_xmit_par().
The ks8851_start_xmit_par() will try to lock struct ks8851_net_par
.lock spinlock, which is already locked by ks8851_irq() from which
ks8851_start_xmit_par() was called. This leads to a deadlock, which
is reported by the kernel, including a trace listed below.
If CONFIG_PREEMPT_RT is not set, then since commit 0913ec336a6c0
("net: ks8851: Fix deadlock with the SPI chip variant") the deadlock
can also be triggered without received packet in the RX FIFO. The
pending softirqs will be processed on return from
spin_unlock_bh(&ks->statelock) in ks8851_irq(), which triggers the
deadlock as well.
Fix the problem by disabling BH around critical sections, including the
IRQ handler, thus preventing the net_tx_action() softirq from triggering
during these critical sections. The net_tx_action() softirq is triggered
once BH are re-enabled and at the end of the IRQ handler, once all the
other IRQ handler actions have been completed.
__schedule from schedule_rtlock+0x1c/0x34
schedule_rtlock from rtlock_slowlock_locked+0x548/0x904
rtlock_slowlock_locked from rt_spin_lock+0x60/0x9c
rt_spin_lock from ks8851_start_xmit_par+0x74/0x1a8
ks8851_start_xmit_par from netdev_start_xmit+0x20/0x44
netdev_start_xmit from dev_hard_start_xmit+0xd0/0x188
dev_hard_start_xmit from sch_direct_xmit+0xb8/0x25c
sch_direct_xmit from __qdisc_run+0x1f8/0x4ec
__qdisc_run from qdisc_run+0x1c/0x28
qdisc_run from net_tx_action+0x1f0/0x268
net_tx_action from handle_softirqs+0x1a4/0x270
handle_softirqs from __local_bh_enable_ip+0xcc/0xe0
__local_bh_enable_ip from __alloc_skb+0xd8/0x128
__alloc_skb from __netdev_alloc_skb+0x3c/0x19c
__netdev_alloc_skb from ks8851_irq+0x388/0x4d4
ks8851_irq from irq_thread_fn+0x24/0x64
irq_thread_fn from irq_thread+0x178/0x28c
irq_thread from kthread+0x12c/0x138
kthread from ret_from_fork+0x14/0x28 |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: avoid early lgr access in smc_clc_wait_msg
A CLC decline can be received while the handshake is still in an early
stage, before the connection has been associated with a link group.
The decline handling in smc_clc_wait_msg() updates link-group level sync
state for first-contact declines, but that state only exists after link
group setup has completed. Guard the link-group update accordingly and
keep the per-socket peer diagnosis handling unchanged.
This preserves the existing sync_err handling for established link-group
contexts and avoids touching link-group state before it is available. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Prevent potential null-ptr-deref in ceph_handle_auth_reply()
If a message of type CEPH_MSG_AUTH_REPLY contains a zero value for both
protocol and result, this is currently not treated as an error. In case
of ac->negotiating == true and ac->protocol > 0, this leads to setting
ac->protocol = 0 and ac->ops = NULL. Thereafter, the check for
ac->protocol != protocol returns false, and init_protocol() is not
called. Subsequently, ac->ops->handle_reply() is called, which leads to
a null pointer dereference, because ac->ops is still NULL.
This patch changes the check for ac->protocol != protocol to
!ac->protocol, as this also includes the case when the protocol was set
to zero in the message. This causes the message to be treated as
containing a bad auth protocol. |
| In the Linux kernel, the following vulnerability has been resolved:
dm mirror: fix integer overflow in create_dirty_log()
The argument count calculation in create_dirty_log() performs
`*args_used = 2 + param_count` before validating against argc. When a
user provides a param_count close to UINT_MAX via the device mapper
table string, this unsigned addition wraps around to a small value,
causing the subsequent `argc < *args_used` check to be bypassed.
The overflowed param_count is then passed as argc to dm_dirty_log_create(),
where it can cause out-of-bounds reads on the argv array.
Fix by comparing param_count against argc - 2 before performing the
addition, following the same pattern used by parse_features() in the
same file. Since argc >= 2 is already guaranteed, the subtraction is
safe. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: ibmasm: fix OOB MMIO read in ibmasm_handle_mouse_interrupt()
ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read
when the queue reader or writer index from hardware exceeds
REMOTE_QUEUE_SIZE (60).
A compromised service processor can trigger this by writing an
out-of-range value to the reader or writer MMIO register before
asserting an interrupt. Since writer is re-read from hardware on
every loop iteration, it can also be set to an out-of-range value
after the loop has already started.
The root cause is that get_queue_reader() and get_queue_writer() return
raw readl() values that are passed directly into get_queue_entry(),
which computes:
queue_begin + reader * sizeof(struct remote_input)
with no bounds check. This unchecked MMIO address is then passed to
memcpy_fromio(), reading 8 bytes from unintended device registers.
For sufficiently large values the address falls outside the PCI BAR
mapping entirely, triggering a machine check exception.
Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of
the loop body, before any call to get_queue_entry(). On an out-of-range
value, reset the reader register to 0 via set_queue_reader() before
breaking, so that normal queue operation can resume if the corrupted
hardware state is transient. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: atmel-aes - Fix 3-page memory leak in atmel_aes_buff_cleanup
atmel_aes_buff_init() allocates 4 pages using __get_free_pages() with
ATMEL_AES_BUFFER_ORDER, but atmel_aes_buff_cleanup() frees only the
first page using free_page(), leaking the remaining 3 pages. Use
free_pages() with ATMEL_AES_BUFFER_ORDER to fix the memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: stop parsing UAC2 rates at MAX_NR_RATES
parse_uac2_sample_rate_range() caps the number of enumerated
rates at MAX_NR_RATES, but it only breaks out of the current
rate loop. A malformed UAC2 RANGE response with additional
triplets continues parsing the remaining triplets and repeatedly
prints "invalid uac2 rates" while probe still holds
register_mutex.
Stop the whole parse once the cap is reached and return the
number of rates collected so far. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: call sk_data_ready() after listener migration
When inet_csk_listen_stop() migrates an established child socket from
a closing listener to another socket in the same SO_REUSEPORT group,
the target listener gets a new accept-queue entry via
inet_csk_reqsk_queue_add(), but that path never notifies the target
listener's waiters. A nonblocking accept() still works because it
checks the queue directly, but poll()/epoll_wait() waiters and
blocking accept() callers can also remain asleep indefinitely.
Call READ_ONCE(nsk->sk_data_ready)(nsk) after a successful migration
in inet_csk_listen_stop().
However, after inet_csk_reqsk_queue_add() succeeds, the ref acquired
in reuseport_migrate_sock() is effectively transferred to
nreq->rsk_listener. Another CPU can then dequeue nreq via accept()
or listener shutdown, hit reqsk_put(), and drop that listener ref.
Since listeners are SOCK_RCU_FREE, wrap the post-queue_add()
dereferences of nsk in rcu_read_lock()/rcu_read_unlock(), which also
covers the existing sock_net(nsk) access in that path.
The reqsk_timer_handler() path does not need the same changes for two
reasons: half-open requests become readable only after the final ACK,
where tcp_child_process() already wakes the listener; and once nreq is
visible via inet_ehash_insert(), the success path no longer touches
nsk directly. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-ntb: Remove duplicate resource teardown
epf_ntb_epc_destroy() duplicates the teardown that the caller is
supposed to do later. This leads to an oops when .allow_link fails or
when .drop_link is performed. Remove the helper.
Also drop pci_epc_put(). EPC device refcounting is tied to configfs EPC
group lifetime, and pci_epc_put() in the .drop_link path is sufficient. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau: fix u32 overflow in pushbuf reloc bounds check
nouveau_gem_pushbuf_reloc_apply() validates each relocation with
if (r->reloc_bo_offset + 4 > nvbo->bo.base.size)
but reloc_bo_offset is __u32 (uapi/drm/nouveau_drm.h) and the integer
literal 4 promotes to unsigned int, so the addition is performed in 32
bits and wraps before the comparison against the size_t bo size.
Cast to u64 so the addition happens in 64-bit arithmetic.
[ Add Fixes: tag. - Danilo ] |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: Handle probe errors properly
The probe procedure of setup_card() in caiaq driver doesn't treat the
error cases gracefully, e.g. the error from snd_card_register() calls
snd_card_free() but continues. This would lead to a UAF for the
further calls like snd_usb_caiaq_control_init(), as Berk suggested in
another patch in the link below.
However, the problem is not only that; in general, this function drops
the all error handlings (as it's a void function) although its caller
can propagate an error to snd_probe(), which eventually calls
snd_card_free() as a proper error path. That said, we should treat
each error case in setup_card(), and just return the error code
promptly, which is then handled later as a fatal error in snd_probe().
This patch achieves it by changing the setup_card() to return an error
code. Also, the superfluous snd_card_free() call is removed, too.
Note that card->private_free can be set still safely at returning an
error. All called functions in card_free() have checks of the
unassigned resources or NULL checks. |
| In the Linux kernel, the following vulnerability has been resolved:
ext2: reject inodes with zero i_nlink and valid mode in ext2_iget()
ext2_iget() already rejects inodes with i_nlink == 0 when i_mode is
zero or i_dtime is set, treating them as deleted. However, the case of
i_nlink == 0 with a non-zero mode and zero dtime slips through. Since
ext2 has no orphan list, such a combination can only result from
filesystem corruption - a legitimate inode deletion always sets either
i_dtime or clears i_mode before freeing the inode.
A crafted image can exploit this gap to present such an inode to the
VFS, which then triggers WARN_ON inside drop_nlink() (fs/inode.c) via
ext2_unlink(), ext2_rename() and ext2_rmdir():
WARNING: CPU: 3 PID: 609 at fs/inode.c:336 drop_nlink+0xad/0xd0 fs/inode.c:336
CPU: 3 UID: 0 PID: 609 Comm: syz-executor Not tainted 6.12.77+ #1
Call Trace:
<TASK>
inode_dec_link_count include/linux/fs.h:2518 [inline]
ext2_unlink+0x26c/0x300 fs/ext2/namei.c:295
vfs_unlink+0x2fc/0x9b0 fs/namei.c:4477
do_unlinkat+0x53e/0x730 fs/namei.c:4541
__x64_sys_unlink+0xc6/0x110 fs/namei.c:4587
do_syscall_64+0xf5/0x220 arch/x86/entry/common.c:78
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
WARNING: CPU: 0 PID: 646 at fs/inode.c:336 drop_nlink+0xad/0xd0 fs/inode.c:336
CPU: 0 UID: 0 PID: 646 Comm: syz.0.17 Not tainted 6.12.77+ #1
Call Trace:
<TASK>
inode_dec_link_count include/linux/fs.h:2518 [inline]
ext2_rename+0x35e/0x850 fs/ext2/namei.c:374
vfs_rename+0xf2f/0x2060 fs/namei.c:5021
do_renameat2+0xbe2/0xd50 fs/namei.c:5178
__x64_sys_rename+0x7e/0xa0 fs/namei.c:5223
do_syscall_64+0xf5/0x220 arch/x86/entry/common.c:78
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
WARNING: CPU: 0 PID: 634 at fs/inode.c:336 drop_nlink+0xad/0xd0 fs/inode.c:336
CPU: 0 UID: 0 PID: 634 Comm: syz-executor Not tainted 6.12.77+ #1
Call Trace:
<TASK>
inode_dec_link_count include/linux/fs.h:2518 [inline]
ext2_rmdir+0xca/0x110 fs/ext2/namei.c:311
vfs_rmdir+0x204/0x690 fs/namei.c:4348
do_rmdir+0x372/0x3e0 fs/namei.c:4407
__x64_sys_unlinkat+0xf0/0x130 fs/namei.c:4577
do_syscall_64+0xf5/0x220 arch/x86/entry/common.c:78
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Extend the existing i_nlink == 0 check to also catch this case,
reporting the corruption via ext2_error() and returning -EFSCORRUPTED.
This rejects the inode at load time and prevents it from reaching any
of the namei.c paths.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: sd: fix missing put_disk() when device_add(&disk_dev) fails
If device_add(&sdkp->disk_dev) fails, put_device() runs
scsi_disk_release(), which frees the scsi_disk but leaves the gendisk
referenced. The device_add_disk() error path in sd_probe() calls
put_disk(gd); call put_disk(gd) here to mirror that cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmasm: fix OOB reads in command_file_write due to missing size checks
The command_file_write() handler allocates a kernel buffer of exactly
count bytes and copies user data into it, but does not validate the
buffer against the dot command protocol before passing it to
get_dot_command_size() and get_dot_command_timeout().
Since both the allocation size (count) and the header fields (command_size,
data_size) are independently user-controlled, an attacker can cause
get_dot_command_size() to return a value exceeding the allocation,
triggering OOB reads in get_dot_command_timeout() and an out-of-bounds
memcpy_toio() that leaks kernel heap memory to the service processor.
Fix with two guards: reject writes smaller than sizeof(struct
dot_command_header) before allocation, then after copying user data
reject commands where the buffer is smaller than the total size declared
by the header (sizeof(header) + command_size + data_size). This ensures
all subsequent header and payload field accesses stay within the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: Fix potentially leftover ep1_in_urb at error path
The previous fix for handling the error from setup_card() missed that
an internal URB cdev->ep1_in_urb might have been already submitted
beforehand. In the normal case, this URB gets killed at the
disconnection, but in the error path, we didn't do it, hence there can
be a potential leak.
Fix it in the error path for setup_card(), too. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nSVM: Sync interrupt shadow to cached vmcb12 after VMRUN of L2
After VMRUN in guest mode, nested_sync_control_from_vmcb02() syncs
fields written by the CPU from vmcb02 to the cached vmcb12. This is
because the cached vmcb12 is used as the authoritative copy of some of
the controls, and is the payload when saving/restoring nested state.
int_state is also written by the CPU, specifically bit 0 (i.e.
SVM_INTERRUPT_SHADOW_MASK) for nested VMs, but it is not sync'd to
cached vmcb12. This does not cause a problem if KVM_SET_NESTED_STATE
preceeds KVM_SET_VCPU_EVENTS in the restore path, as an interrupt shadow
would be correctly restored to vmcb02 (KVM_SET_VCPU_EVENTS overwrites
what KVM_SET_NESTED_STATE restored in int_state).
However, if KVM_SET_VCPU_EVENTS preceeds KVM_SET_NESTED_STATE, an
interrupt shadow would be restored into vmcb01 instead of vmcb02. This
would mostly be benign for L1 (delays an interrupt), but not for L2. For
L2, the vCPU could hang (e.g. if a wakeup interrupt is delivered before
a HLT that should have been in an interrupt shadow).
Sync int_state to the cached vmcb12 in nested_sync_control_from_vmcb02()
to avoid this problem. With that, KVM_SET_NESTED_STATE restores the
correct interrupt shadow state, and if KVM_SET_VCPU_EVENTS follows it
would overwrite it with the same value. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccree - fix a memory leak in cc_mac_digest()
Add cc_unmap_result() if cc_map_hash_request_final()
fails to prevent potential memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
bareudp: fix NULL pointer dereference in bareudp_fill_metadata_dst()
bareudp_fill_metadata_dst() passes bareudp->sock to
udp_tunnel6_dst_lookup() in the IPv6 path without a NULL check.
The socket is only created in bareudp_open() and NULLed in
bareudp_stop(), so calling this function while the device is down
triggers a NULL dereference via sock->sk.
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:udp_tunnel6_dst_lookup (net/ipv6/ip6_udp_tunnel.c:160)
Call Trace:
<TASK>
bareudp_fill_metadata_dst (drivers/net/bareudp.c:532)
do_execute_actions (net/openvswitch/actions.c:901)
ovs_execute_actions (net/openvswitch/actions.c:1589)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:700)
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1114)
genl_rcv_msg (net/netlink/genetlink.c:1209)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
</TASK>
Add a NULL check returning -ESHUTDOWN, consistent with the xmit paths
in the same driver. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: arp_tables: fix IEEE1394 ARP payload parsing
Weiming Shi says:
"arp_packet_match() unconditionally parses the ARP payload assuming two
hardware addresses are present (source and target). However,
IPv4-over-IEEE1394 ARP (RFC 2734) omits the target hardware address
field, and arp_hdr_len() already accounts for this by returning a
shorter length for ARPHRD_IEEE1394 devices.
As a result, on IEEE1394 interfaces arp_packet_match() advances past a
nonexistent target hardware address and reads the wrong bytes for both
the target device address comparison and the target IP address. This
causes arptables rules to match against garbage data, leading to
incorrect filtering decisions: packets that should be accepted may be
dropped and vice versa.
The ARP stack in net/ipv4/arp.c (arp_create and arp_process) already
handles this correctly by skipping the target hardware address for
ARPHRD_IEEE1394. Apply the same pattern to arp_packet_match()."
Mangle the original patch to always return 0 (no match) in case user
matches on the target hardware address which is never present in
IEEE1394.
Note that this returns 0 (no match) for either normal and inverse match
because matching in the target hardware address in ARPHRD_IEEE1394 has
never been supported by arptables. This is intentional, matching on the
target hardware address should never evaluate true for ARPHRD_IEEE1394.
Moreover, adjust arpt_mangle to drop the packet too as AI suggests:
In arpt_mangle, the logic assumes a standard ARP layout. Because
IEEE1394 (FireWire) omits the target hardware address, the linear
pointer arithmetic miscalculates the offset for the target IP address.
This causes mangling operations to write to the wrong location, leading
to packet corruption. To ensure safety, this patch drops packets
(NF_DROP) when mangling is requested for these fields on IEEE1394
devices, as the current implementation cannot correctly map the FireWire
ARP payload.
This omits both mangling target hardware and IP address. Even if IP
address mangling should be possible in IEEE1394, this would require
to adjust arpt_mangle offset calculation, which has never been
supported.
Based on patch from Weiming Shi <bestswngs@gmail.com>. |
