| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: don't zero the entire extent if EXT4_EXT_DATA_PARTIAL_VALID1
When allocating initialized blocks from a large unwritten extent, or
when splitting an unwritten extent during end I/O and converting it to
initialized, there is currently a potential issue of stale data if the
extent needs to be split in the middle.
0 A B N
[UUUUUUUUUUUU] U: unwritten extent
[--DDDDDDDD--] D: valid data
|<- ->| ----> this range needs to be initialized
ext4_split_extent() first try to split this extent at B with
EXT4_EXT_DATA_ENTIRE_VALID1 and EXT4_EXT_MAY_ZEROOUT flag set, but
ext4_split_extent_at() failed to split this extent due to temporary lack
of space. It zeroout B to N and mark the entire extent from 0 to N
as written.
0 A B N
[WWWWWWWWWWWW] W: written extent
[SSDDDDDDDDZZ] Z: zeroed, S: stale data
ext4_split_extent() then try to split this extent at A with
EXT4_EXT_DATA_VALID2 flag set. This time, it split successfully and left
a stale written extent from 0 to A.
0 A B N
[WW|WWWWWWWWWW]
[SS|DDDDDDDDZZ]
Fix this by pass EXT4_EXT_DATA_PARTIAL_VALID1 to ext4_split_extent_at()
when splitting at B, don't convert the entire extent to written and left
it as unwritten after zeroing out B to N. The remaining work is just
like the standard two-part split. ext4_split_extent() will pass the
EXT4_EXT_DATA_VALID2 flag when it calls ext4_split_extent_at() for the
second time, allowing it to properly handle the split. If the split is
successful, it will keep extent from 0 to A as unwritten. |
| In the Linux kernel, the following vulnerability has been resolved:
mfd: arizona: Fix regulator resource leak on wm5102_clear_write_sequencer() failure
The wm5102_clear_write_sequencer() helper may return an error
and just return, bypassing the cleanup sequence and causing
regulators to remain enabled, leading to a resource leak.
Change the direct return to jump to the err_reset label to
properly free the resources. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: pm8916_bms_vm: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: avoid per-cpu hold underflow in aa_get_buffer
When aa_get_buffer() pulls from the per-cpu list it unconditionally
decrements cache->hold. If hold reaches 0 while count is still non-zero,
the unsigned decrement wraps to UINT_MAX. This keeps hold non-zero for a
very long time, so aa_put_buffer() never returns buffers to the global
list, which can starve other CPUs and force repeated kmalloc(aa_g_path_max)
allocations.
Guard the decrement so hold never underflows. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: cpcap-battery: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Fix memleak of newsk in unix_stream_connect().
When prepare_peercred() fails in unix_stream_connect(),
unix_release_sock() is not called for newsk, and the memory
is leaked.
Let's move prepare_peercred() before unix_create1(). |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: core - use RCU and work_struct to fix race condition
Currently, hwrng_fill is not cleared until the hwrng_fillfn() thread
exits. Since hwrng_unregister() reads hwrng_fill outside the rng_mutex
lock, a concurrent hwrng_unregister() may call kthread_stop() again on
the same task.
Additionally, if hwrng_unregister() is called immediately after
hwrng_register(), the stopped thread may have never been executed. Thus,
hwrng_fill remains dirty even after hwrng_unregister() returns. In this
case, subsequent calls to hwrng_register() will fail to start new
threads, and hwrng_unregister() will call kthread_stop() on the same
freed task. In both cases, a use-after-free occurs:
refcount_t: addition on 0; use-after-free.
WARNING: ... at lib/refcount.c:25 refcount_warn_saturate+0xec/0x1c0
Call Trace:
kthread_stop+0x181/0x360
hwrng_unregister+0x288/0x380
virtrng_remove+0xe3/0x200
This patch fixes the race by protecting the global hwrng_fill pointer
inside the rng_mutex lock, so that hwrng_fillfn() thread is stopped only
once, and calls to kthread_run() and kthread_stop() are serialized
with the lock held.
To avoid deadlock in hwrng_fillfn() while being stopped with the lock
held, we convert current_rng to RCU, so that get_current_rng() can read
current_rng without holding the lock. To remove the lock from put_rng(),
we also delay the actual cleanup into a work_struct.
Since get_current_rng() no longer returns ERR_PTR values, the IS_ERR()
checks are removed from its callers.
With hwrng_fill protected by the rng_mutex lock, hwrng_fillfn() can no
longer clear hwrng_fill itself. Therefore, if hwrng_fillfn() returns
directly after current_rng is dropped, kthread_stop() would be called on
a freed task_struct later. To fix this, hwrng_fillfn() calls schedule()
now to keep the task alive until being stopped. The kthread_stop() call
is also moved from hwrng_unregister() to drop_current_rng(), ensuring
kthread_stop() is called on all possible paths where current_rng becomes
NULL, so that the thread would not wait forever. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SDCA: Add allocation failure check for Entity name
Currently find_sdca_entity_iot() can allocate a string for the
Entity name but it doesn't check if that allocation succeeded.
Add the missing NULL check after the allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
net: annotate data-races around sk->sk_{data_ready,write_space}
skmsg (and probably other layers) are changing these pointers
while other cpus might read them concurrently.
Add corresponding READ_ONCE()/WRITE_ONCE() annotations
for UDP, TCP and AF_UNIX. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: Don't log plaintext credentials in cifs_set_cifscreds
When debug logging is enabled, cifs_set_cifscreds() logs the key
payload and exposes the plaintext username and password. Remove the
debug log to avoid exposing credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix NULL pointer deref in ip6_rt_get_dev_rcu()
l3mdev_master_dev_rcu() can return NULL when the slave device is being
un-slaved from a VRF. All other callers deal with this, but we lost
the fallback to loopback in ip6_rt_pcpu_alloc() -> ip6_rt_get_dev_rcu()
with commit 4832c30d5458 ("net: ipv6: put host and anycast routes on
device with address").
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:ip6_rt_pcpu_alloc (net/ipv6/route.c:1418)
Call Trace:
ip6_pol_route (net/ipv6/route.c:2318)
fib6_rule_lookup (net/ipv6/fib6_rules.c:115)
ip6_route_output_flags (net/ipv6/route.c:2607)
vrf_process_v6_outbound (drivers/net/vrf.c:437)
I was tempted to rework the un-slaving code to clear the flag first
and insert synchronize_rcu() before we remove the upper. But looks like
the explicit fallback to loopback_dev is an established pattern.
And I guess avoiding the synchronize_rcu() is nice, too. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/rocket: fix unwinding in error path in rocket_probe
When rocket_core_init() fails (as could be the case with EPROBE_DEFER),
we need to properly unwind by decrementing the counter we just
incremented and if this is the first core we failed to probe, remove the
rocket DRM device with rocket_device_fini() as well. This matches the
logic in rocket_remove(). Failing to properly unwind results in
out-of-bounds accesses. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Fix use-after-free in pm8001_queue_command()
Commit e29c47fe8946 ("scsi: pm8001: Simplify pm8001_task_exec()") refactors
pm8001_queue_command(), however it introduces a potential cause of a double
free scenario when it changes the function to return -ENODEV in case of phy
down/device gone state.
In this path, pm8001_queue_command() updates task status and calls
task_done to indicate to upper layer that the task has been handled.
However, this also frees the underlying SAS task. A -ENODEV is then
returned to the caller. When libsas sas_ata_qc_issue() receives this error
value, it assumes the task wasn't handled/queued by LLDD and proceeds to
clean up and free the task again, resulting in a double free.
Since pm8001_queue_command() handles the SAS task in this case, it should
return 0 to the caller indicating that the task has been handled. |
| In the Linux kernel, the following vulnerability has been resolved:
xen-netback: reject zero-queue configuration from guest
A malicious or buggy Xen guest can write "0" to the xenbus key
"multi-queue-num-queues". The connect() function in the backend only
validates the upper bound (requested_num_queues > xenvif_max_queues)
but not zero, allowing requested_num_queues=0 to reach
vzalloc(array_size(0, sizeof(struct xenvif_queue))), which triggers
WARN_ON_ONCE(!size) in __vmalloc_node_range().
On systems with panic_on_warn=1, this allows a guest-to-host denial
of service.
The Xen network interface specification requires
the queue count to be "greater than zero".
Add a zero check to match the validation already present
in xen-blkback, which has included this
guard since its multi-queue support was added. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hns3: fix double free issue for tx spare buffer
In hns3_set_ringparam(), a temporary copy (tmp_rings) of the ring structure
is created for rollback. However, the tx_spare pointer in the original
ring handle is incorrectly left pointing to the old backup memory.
Later, if memory allocation fails in hns3_init_all_ring() during the setup,
the error path attempts to free all newly allocated rings. Since tx_spare
contains a stale (non-NULL) pointer from the backup, it is mistaken for
a newly allocated buffer and is erroneously freed, leading to a double-free
of the backup memory.
The root cause is that the tx_spare field was not cleared after its value
was saved in tmp_rings, leaving a dangling pointer.
Fix this by setting tx_spare to NULL in the original ring structure
when the creation of the new `tx_spare` fails. This ensures the
error cleanup path only frees genuinely newly allocated buffers. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: Fix & Optimize table creation from possibly unaligned memory
Source blob may come from userspace and might be unaligned.
Try to optize the copying process by avoiding unaligned memory accesses.
- Added Fixes tag
- Added "Fix &" to description as this doesn't just optimize but fixes
a potential unaligned memory access
[jj: remove duplicate word "convert" in comment trigger checkpatch warning] |
| In the Linux kernel, the following vulnerability has been resolved:
quota: fix livelock between quotactl and freeze_super
When a filesystem is frozen, quotactl_block() enters a retry loop
waiting for the filesystem to thaw. It acquires s_umount, checks the
freeze state, drops s_umount and uses sb_start_write() - sb_end_write()
pair to wait for the unfreeze.
However, this retry loop can trigger a livelock issue, specifically on
kernels with preemption disabled.
The mechanism is as follows:
1. freeze_super() sets SB_FREEZE_WRITE and calls sb_wait_write().
2. sb_wait_write() calls percpu_down_write(), which initiates
synchronize_rcu().
3. Simultaneously, quotactl_block() spins in its retry loop, immediately
executing the sb_start_write() - sb_end_write() pair.
4. Because the kernel is non-preemptible and the loop contains no
scheduling points, quotactl_block() never yields the CPU. This
prevents that CPU from reaching an RCU quiescent state.
5. synchronize_rcu() in the freezer thread waits indefinitely for the
quotactl_block() CPU to report a quiescent state.
6. quotactl_block() spins indefinitely waiting for the freezer to
advance, which it cannot do as it is blocked on the RCU sync.
This results in a hang of the freezer process and 100% CPU usage by the
quota process.
While this can occur intermittently on multi-core systems, it is
reliably reproducing on a node with the following script, running both
the freezer and the quota toggle on the same CPU:
# mkfs.ext4 -O quota /dev/sda 2g && mkdir a_mount
# mount /dev/sda -o quota,usrquota,grpquota a_mount
# taskset -c 3 bash -c "while true; do xfs_freeze -f a_mount; \
xfs_freeze -u a_mount; done" &
# taskset -c 3 bash -c "while true; do quotaon a_mount; \
quotaoff a_mount; done" &
Adding cond_resched() to the retry loop fixes the issue. It acts as an
RCU quiescent state, allowing synchronize_rcu() in percpu_down_write()
to complete. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: sbs-battery: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. Keep the old behavior of
just printing a warning in case of any failures during the IRQ request
and finishing the probe successfully. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix dirtyclusters double decrement on fs shutdown
fstests test generic/388 occasionally reproduces a warning in
ext4_put_super() associated with the dirty clusters count:
WARNING: CPU: 7 PID: 76064 at fs/ext4/super.c:1324 ext4_put_super+0x48c/0x590 [ext4]
Tracing the failure shows that the warning fires due to an
s_dirtyclusters_counter value of -1. IOW, this appears to be a
spurious decrement as opposed to some sort of leak. Further tracing
of the dirty cluster count deltas and an LLM scan of the resulting
output identified the cause as a double decrement in the error path
between ext4_mb_mark_diskspace_used() and the caller
ext4_mb_new_blocks().
First, note that generic/388 is a shutdown vs. fsstress test and so
produces a random set of operations and shutdown injections. In the
problematic case, the shutdown triggers an error return from the
ext4_handle_dirty_metadata() call(s) made from
ext4_mb_mark_context(). The changed value is non-zero at this point,
so ext4_mb_mark_diskspace_used() does not exit after the error
bubbles up from ext4_mb_mark_context(). Instead, the former
decrements both cluster counters and returns the error up to
ext4_mb_new_blocks(). The latter falls into the !ar->len out path
which decrements the dirty clusters counter a second time, creating
the inconsistency.
To avoid this problem and simplify ownership of the cluster
reservation in this codepath, lift the counter reduction to a single
place in the caller. This makes it more clear that
ext4_mb_new_blocks() is responsible for acquiring cluster
reservation (via ext4_claim_free_clusters()) in the !delalloc case
as well as releasing it, regardless of whether it ends up consumed
or returned due to failure. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Require frozen map for calculating map hash
Currently, bpf_map_get_info_by_fd calculates and caches the hash of the
map regardless of the map's frozen state.
This leads to a TOCTOU bug where userspace can call
BPF_OBJ_GET_INFO_BY_FD to cache the hash and then modify the map
contents before freezing.
Therefore, a trusted loader can be tricked into verifying the stale hash
while loading the modified contents.
Fix this by returning -EPERM if the map is not frozen when the hash is
requested. This ensures the hash is only generated for the final,
immutable state of the map. |
