| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: ufs-qcom: Fix UFS OCP issue during UFS power down (PC=3)
According to UFS specifications, the power-off sequence for a UFS device
includes:
- Sending an SSU command with Power_Condition=3 and await a response.
- Asserting RST_N low.
- Turning off REF_CLK.
- Turning off VCC.
- Turning off VCCQ/VCCQ2.
As part of ufs shutdown, after the SSU command completion, asserting
hardware reset (HWRST) triggers the device firmware to wake up and
execute its reset routine. This routine initializes hardware blocks and
takes a few milliseconds to complete. During this time, the ICCQ draws a
large current.
This large ICCQ current may cause issues for the regulator which is
supplying power to UFS, because the turn off request from UFS driver to
the regulator framework will be immediately followed by low power
mode(LPM) request by regulator framework. This is done by framework
because UFS which is the only client is requesting for disable. So if
the rail is still in the process of shutting down while ICCQ exceeds LPM
current thresholds, and LPM mode is activated in hardware during this
state, it may trigger an overcurrent protection (OCP) fault in the
regulator.
To prevent this, a 10ms delay is added after asserting HWRST. This
allows the reset operation to complete while power rails remain active
and in high-power mode.
Currently there is no way for Host to query whether the reset is
completed or not and hence this the delay is based on experiments with
Qualcomm UFS controllers across multiple UFS vendors. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: avoid having an active sc_timer before freeing sci
Because kthread_stop did not stop sc_task properly and returned -EINTR,
the sc_timer was not properly closed, ultimately causing the problem [1]
reported by syzbot when freeing sci due to the sc_timer not being closed.
Because the thread sc_task main function nilfs_segctor_thread() returns 0
when it succeeds, when the return value of kthread_stop() is not 0 in
nilfs_segctor_destroy(), we believe that it has not properly closed
sc_timer.
We use timer_shutdown_sync() to sync wait for sc_timer to shutdown, and
set the value of sc_task to NULL under the protection of lock
sc_state_lock, so as to avoid the issue caused by sc_timer not being
properly shutdowned.
[1]
ODEBUG: free active (active state 0) object: 00000000dacb411a object type: timer_list hint: nilfs_construction_timeout
Call trace:
nilfs_segctor_destroy fs/nilfs2/segment.c:2811 [inline]
nilfs_detach_log_writer+0x668/0x8cc fs/nilfs2/segment.c:2877
nilfs_put_super+0x4c/0x12c fs/nilfs2/super.c:509 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
When smb1 mount fails, KASAN detect slab-out-of-bounds in
init_smb2_rsp_hdr like the following one.
For smb1 negotiate(56bytes) , init_smb2_rsp_hdr() for smb2 is called.
The issue occurs while handling smb1 negotiate as smb2 server operations.
Add smb server operations for smb1 (get_cmd_val, init_rsp_hdr,
allocate_rsp_buf, check_user_session) to handle smb1 negotiate so that
smb2 server operation does not handle it.
[ 411.400423] CIFS: VFS: Use of the less secure dialect vers=1.0 is
not recommended unless required for access to very old servers
[ 411.400452] CIFS: Attempting to mount \\192.168.45.139\homes
[ 411.479312] ksmbd: init_smb2_rsp_hdr : 492
[ 411.479323] ==================================================================
[ 411.479327] BUG: KASAN: slab-out-of-bounds in
init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479369] Read of size 16 at addr ffff888488ed0734 by task kworker/14:1/199
[ 411.479379] CPU: 14 PID: 199 Comm: kworker/14:1 Tainted: G
OE 6.1.21 #3
[ 411.479386] Hardware name: ASUSTeK COMPUTER INC. Z10PA-D8
Series/Z10PA-D8 Series, BIOS 3801 08/23/2019
[ 411.479390] Workqueue: ksmbd-io handle_ksmbd_work [ksmbd]
[ 411.479425] Call Trace:
[ 411.479428] <TASK>
[ 411.479432] dump_stack_lvl+0x49/0x63
[ 411.479444] print_report+0x171/0x4a8
[ 411.479452] ? kasan_complete_mode_report_info+0x3c/0x200
[ 411.479463] ? init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479497] kasan_report+0xb4/0x130
[ 411.479503] ? init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479537] kasan_check_range+0x149/0x1e0
[ 411.479543] memcpy+0x24/0x70
[ 411.479550] init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479585] handle_ksmbd_work+0x109/0x760 [ksmbd]
[ 411.479616] ? _raw_spin_unlock_irqrestore+0x50/0x50
[ 411.479624] ? smb3_encrypt_resp+0x340/0x340 [ksmbd]
[ 411.479656] process_one_work+0x49c/0x790
[ 411.479667] worker_thread+0x2b1/0x6e0
[ 411.479674] ? process_one_work+0x790/0x790
[ 411.479680] kthread+0x177/0x1b0
[ 411.479686] ? kthread_complete_and_exit+0x30/0x30
[ 411.479692] ret_from_fork+0x22/0x30
[ 411.479702] </TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: always release netdev hooks from notifier
This reverts "netfilter: nf_tables: skip netdev events generated on netns removal".
The problem is that when a veth device is released, the veth release
callback will also queue the peer netns device for removal.
Its possible that the peer netns is also slated for removal. In this
case, the device memory is already released before the pre_exit hook of
the peer netns runs:
BUG: KASAN: slab-use-after-free in nf_hook_entry_head+0x1b8/0x1d0
Read of size 8 at addr ffff88812c0124f0 by task kworker/u8:1/45
Workqueue: netns cleanup_net
Call Trace:
nf_hook_entry_head+0x1b8/0x1d0
__nf_unregister_net_hook+0x76/0x510
nft_netdev_unregister_hooks+0xa0/0x220
__nft_release_hook+0x184/0x490
nf_tables_pre_exit_net+0x12f/0x1b0
..
Order is:
1. First netns is released, veth_dellink() queues peer netns device
for removal
2. peer netns is queued for removal
3. peer netns device is released, unreg event is triggered
4. unreg event is ignored because netns is going down
5. pre_exit hook calls nft_netdev_unregister_hooks but device memory
might be free'd already. |
| In the Linux kernel, the following vulnerability has been resolved:
netconsole: Acquire su_mutex before navigating configs hierarchy
There is a race between operations that iterate over the userdata
cg_children list and concurrent add/remove of userdata items through
configfs. The update_userdata() function iterates over the
nt->userdata_group.cg_children list, and count_extradata_entries() also
iterates over this same list to count nodes.
Quoting from Documentation/filesystems/configfs.rst:
> A subsystem can navigate the cg_children list and the ci_parent pointer
> to see the tree created by the subsystem. This can race with configfs'
> management of the hierarchy, so configfs uses the subsystem mutex to
> protect modifications. Whenever a subsystem wants to navigate the
> hierarchy, it must do so under the protection of the subsystem
> mutex.
Without proper locking, if a userdata item is added or removed
concurrently while these functions are iterating, the list can be
accessed in an inconsistent state. For example, the list_for_each() loop
can reach a node that is being removed from the list by list_del_init()
which sets the nodes' .next pointer to point to itself, so the loop will
never end (or reach the WARN_ON_ONCE in update_userdata() ).
Fix this by holding the configfs subsystem mutex (su_mutex) during all
operations that iterate over cg_children.
This includes:
- userdatum_value_store() which calls update_userdata() to iterate over
cg_children
- All sysdata_*_enabled_store() functions which call
count_extradata_entries() to iterate over cg_children
The su_mutex must be acquired before dynamic_netconsole_mutex to avoid
potential lock ordering issues, as configfs operations may already hold
su_mutex when calling into our code. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Prevent recursive memory reclaim
Function new_inode() returns a new inode with inode->i_mapping->gfp_mask
set to GFP_HIGHUSER_MOVABLE. This value includes the __GFP_FS flag, so
allocations in that address space can recurse into filesystem memory
reclaim. We don't want that to happen because it can consume a
significant amount of stack memory.
Worse than that is that it can also deadlock: for example, in several
places, gfs2_unstuff_dinode() is called inside filesystem transactions.
This calls filemap_grab_folio(), which can allocate a new folio, which
can trigger memory reclaim. If memory reclaim recurses into the
filesystem and starts another transaction, a deadlock will ensue.
To fix these kinds of problems, prevent memory reclaim from recursing
into filesystem code by making sure that the gfp_mask of inode address
spaces doesn't include __GFP_FS.
The "meta" and resource group address spaces were already using GFP_NOFS
as their gfp_mask (which doesn't include __GFP_FS). The default value
of GFP_HIGHUSER_MOVABLE is less restrictive than GFP_NOFS, though. To
avoid being overly limiting, use the default value and only knock off
the __GFP_FS flag. I'm not sure if this will actually make a
difference, but it also shouldn't hurt.
This patch is loosely based on commit ad22c7a043c2 ("xfs: prevent stack
overflows from page cache allocation").
Fixes xfstest generic/273. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: fix out-of-bounds access in tty_driver_lookup_tty()
When specifying an invalid console= device like console=tty3270,
tty_driver_lookup_tty() returns the tty struct without checking
whether index is a valid number.
To reproduce:
qemu-system-x86_64 -enable-kvm -nographic -serial mon:stdio \
-kernel ../linux-build-x86/arch/x86/boot/bzImage \
-append "console=ttyS0 console=tty3270"
This crashes with:
[ 0.770599] BUG: kernel NULL pointer dereference, address: 00000000000000ef
[ 0.771265] #PF: supervisor read access in kernel mode
[ 0.771773] #PF: error_code(0x0000) - not-present page
[ 0.772609] Oops: 0000 [#1] PREEMPT SMP PTI
[ 0.774878] RIP: 0010:tty_open+0x268/0x6f0
[ 0.784013] chrdev_open+0xbd/0x230
[ 0.784444] ? cdev_device_add+0x80/0x80
[ 0.784920] do_dentry_open+0x1e0/0x410
[ 0.785389] path_openat+0xca9/0x1050
[ 0.785813] do_filp_open+0xaa/0x150
[ 0.786240] file_open_name+0x133/0x1b0
[ 0.786746] filp_open+0x27/0x50
[ 0.787244] console_on_rootfs+0x14/0x4d
[ 0.787800] kernel_init_freeable+0x1e4/0x20d
[ 0.788383] ? rest_init+0xc0/0xc0
[ 0.788881] kernel_init+0x11/0x120
[ 0.789356] ret_from_fork+0x22/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: use kvmalloc_array/kvfree instead of kmalloc_array/kfree
The call stack shown below is a scenario in the Linux 4.19 kernel.
Allocating memory failed where exfat fs use kmalloc_array due to
system memory fragmentation, while the u-disk was inserted without
recognition.
Devices such as u-disk using the exfat file system are pluggable and
may be insert into the system at any time.
However, long-term running systems cannot guarantee the continuity of
physical memory. Therefore, it's necessary to address this issue.
Binder:2632_6: page allocation failure: order:4,
mode:0x6040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
Call trace:
[242178.097582] dump_backtrace+0x0/0x4
[242178.097589] dump_stack+0xf4/0x134
[242178.097598] warn_alloc+0xd8/0x144
[242178.097603] __alloc_pages_nodemask+0x1364/0x1384
[242178.097608] kmalloc_order+0x2c/0x510
[242178.097612] kmalloc_order_trace+0x40/0x16c
[242178.097618] __kmalloc+0x360/0x408
[242178.097624] load_alloc_bitmap+0x160/0x284
[242178.097628] exfat_fill_super+0xa3c/0xe7c
[242178.097635] mount_bdev+0x2e8/0x3a0
[242178.097638] exfat_fs_mount+0x40/0x50
[242178.097643] mount_fs+0x138/0x2e8
[242178.097649] vfs_kern_mount+0x90/0x270
[242178.097655] do_mount+0x798/0x173c
[242178.097659] ksys_mount+0x114/0x1ac
[242178.097665] __arm64_sys_mount+0x24/0x34
[242178.097671] el0_svc_common+0xb8/0x1b8
[242178.097676] el0_svc_handler+0x74/0x90
[242178.097681] el0_svc+0x8/0x340
By analyzing the exfat code,we found that continuous physical memory
is not required here,so kvmalloc_array is used can solve this problem. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to check readonly condition correctly
With below case, it can mount multi-device image w/ rw option, however
one of secondary device is set as ro, later update will cause panic, so
let's introduce f2fs_dev_is_readonly(), and check multi-devices rw status
in f2fs_remount() w/ it in order to avoid such inconsistent mount status.
mkfs.f2fs -c /dev/zram1 /dev/zram0 -f
blockdev --setro /dev/zram1
mount -t f2fs dev/zram0 /mnt/f2fs
mount: /mnt/f2fs: WARNING: source write-protected, mounted read-only.
mount -t f2fs -o remount,rw mnt/f2fs
dd if=/dev/zero of=/mnt/f2fs/file bs=1M count=8192
kernel BUG at fs/f2fs/inline.c:258!
RIP: 0010:f2fs_write_inline_data+0x23e/0x2d0 [f2fs]
Call Trace:
f2fs_write_single_data_page+0x26b/0x9f0 [f2fs]
f2fs_write_cache_pages+0x389/0xa60 [f2fs]
__f2fs_write_data_pages+0x26b/0x2d0 [f2fs]
f2fs_write_data_pages+0x2e/0x40 [f2fs]
do_writepages+0xd3/0x1b0
__writeback_single_inode+0x5b/0x420
writeback_sb_inodes+0x236/0x5a0
__writeback_inodes_wb+0x56/0xf0
wb_writeback+0x2a3/0x490
wb_do_writeback+0x2b2/0x330
wb_workfn+0x6a/0x260
process_one_work+0x270/0x5e0
worker_thread+0x52/0x3e0
kthread+0xf4/0x120
ret_from_fork+0x29/0x50 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: phy: fsl-usb: Fix use-after-free in delayed work during device removal
The delayed work item otg_event is initialized in fsl_otg_conf() and
scheduled under two conditions:
1. When a host controller binds to the OTG controller.
2. When the USB ID pin state changes (cable insertion/removal).
A race condition occurs when the device is removed via fsl_otg_remove():
the fsl_otg instance may be freed while the delayed work is still pending
or executing. This leads to use-after-free when the work function
fsl_otg_event() accesses the already freed memory.
The problematic scenario:
(detach thread) | (delayed work)
fsl_otg_remove() |
kfree(fsl_otg_dev) //FREE| fsl_otg_event()
| og = container_of(...) //USE
| og-> //USE
Fix this by calling disable_delayed_work_sync() in fsl_otg_remove()
before deallocating the fsl_otg structure. This ensures the delayed work
is properly canceled and completes execution prior to memory deallocation.
This bug was identified through static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix issue in verifying allow_ptr_leaks
After we converted the capabilities of our networking-bpf program from
cap_sys_admin to cap_net_admin+cap_bpf, our networking-bpf program
failed to start. Because it failed the bpf verifier, and the error log
is "R3 pointer comparison prohibited".
A simple reproducer as follows,
SEC("cls-ingress")
int ingress(struct __sk_buff *skb)
{
struct iphdr *iph = (void *)(long)skb->data + sizeof(struct ethhdr);
if ((long)(iph + 1) > (long)skb->data_end)
return TC_ACT_STOLEN;
return TC_ACT_OK;
}
Per discussion with Yonghong and Alexei [1], comparison of two packet
pointers is not a pointer leak. This patch fixes it.
Our local kernel is 6.1.y and we expect this fix to be backported to
6.1.y, so stable is CCed.
[1]. https://lore.kernel.org/bpf/CAADnVQ+Nmspr7Si+pxWn8zkE7hX-7s93ugwC+94aXSy4uQ9vBg@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Disable preemption in bpf_event_output
We received report [1] of kernel crash, which is caused by
using nesting protection without disabled preemption.
The bpf_event_output can be called by programs executed by
bpf_prog_run_array_cg function that disabled migration but
keeps preemption enabled.
This can cause task to be preempted by another one inside the
nesting protection and lead eventually to two tasks using same
perf_sample_data buffer and cause crashes like:
BUG: kernel NULL pointer dereference, address: 0000000000000001
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
...
? perf_output_sample+0x12a/0x9a0
? finish_task_switch.isra.0+0x81/0x280
? perf_event_output+0x66/0xa0
? bpf_event_output+0x13a/0x190
? bpf_event_output_data+0x22/0x40
? bpf_prog_dfc84bbde731b257_cil_sock4_connect+0x40a/0xacb
? xa_load+0x87/0xe0
? __cgroup_bpf_run_filter_sock_addr+0xc1/0x1a0
? release_sock+0x3e/0x90
? sk_setsockopt+0x1a1/0x12f0
? udp_pre_connect+0x36/0x50
? inet_dgram_connect+0x93/0xa0
? __sys_connect+0xb4/0xe0
? udp_setsockopt+0x27/0x40
? __pfx_udp_push_pending_frames+0x10/0x10
? __sys_setsockopt+0xdf/0x1a0
? __x64_sys_connect+0xf/0x20
? do_syscall_64+0x3a/0x90
? entry_SYSCALL_64_after_hwframe+0x72/0xdc
Fixing this by disabling preemption in bpf_event_output.
[1] https://github.com/cilium/cilium/issues/26756 |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix memory leak of iter->temp when reading trace_pipe
kmemleak reports:
unreferenced object 0xffff88814d14e200 (size 256):
comm "cat", pid 336, jiffies 4294871818 (age 779.490s)
hex dump (first 32 bytes):
04 00 01 03 00 00 00 00 08 00 00 00 00 00 00 00 ................
0c d8 c8 9b ff ff ff ff 04 5a ca 9b ff ff ff ff .........Z......
backtrace:
[<ffffffff9bdff18f>] __kmalloc+0x4f/0x140
[<ffffffff9bc9238b>] trace_find_next_entry+0xbb/0x1d0
[<ffffffff9bc9caef>] trace_print_lat_context+0xaf/0x4e0
[<ffffffff9bc94490>] print_trace_line+0x3e0/0x950
[<ffffffff9bc95499>] tracing_read_pipe+0x2d9/0x5a0
[<ffffffff9bf03a43>] vfs_read+0x143/0x520
[<ffffffff9bf04c2d>] ksys_read+0xbd/0x160
[<ffffffff9d0f0edf>] do_syscall_64+0x3f/0x90
[<ffffffff9d2000aa>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
when reading file 'trace_pipe', 'iter->temp' is allocated or relocated
in trace_find_next_entry() but not freed before 'trace_pipe' is closed.
To fix it, free 'iter->temp' in tracing_release_pipe(). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: don't free qgroup space unless specified
Boris noticed in his simple quotas testing that he was getting a leak
with Sweet Tea's change to subvol create that stopped doing a
transaction commit. This was just a side effect of that change.
In the delayed inode code we have an optimization that will free extra
reservations if we think we can pack a dir item into an already modified
leaf. Previously this wouldn't be triggered in the subvolume create
case because we'd commit the transaction, it was still possible but
much harder to trigger. It could actually be triggered if we did a
mkdir && subvol create with qgroups enabled.
This occurs because in btrfs_insert_delayed_dir_index(), which gets
called when we're adding the dir item, we do the following:
btrfs_block_rsv_release(fs_info, trans->block_rsv, bytes, NULL);
if we're able to skip reserving space.
The problem here is that trans->block_rsv points at the temporary block
rsv for the subvolume create, which has qgroup reservations in the block
rsv.
This is a problem because btrfs_block_rsv_release() will do the
following:
if (block_rsv->qgroup_rsv_reserved >= block_rsv->qgroup_rsv_size) {
qgroup_to_release = block_rsv->qgroup_rsv_reserved -
block_rsv->qgroup_rsv_size;
block_rsv->qgroup_rsv_reserved = block_rsv->qgroup_rsv_size;
}
The temporary block rsv just has ->qgroup_rsv_reserved set,
->qgroup_rsv_size == 0. The optimization in
btrfs_insert_delayed_dir_index() sets ->qgroup_rsv_reserved = 0. Then
later on when we call btrfs_subvolume_release_metadata() which has
btrfs_block_rsv_release(fs_info, rsv, (u64)-1, &qgroup_to_release);
btrfs_qgroup_convert_reserved_meta(root, qgroup_to_release);
qgroup_to_release is set to 0, and we do not convert the reserved
metadata space.
The problem here is that the block rsv code has been unconditionally
messing with ->qgroup_rsv_reserved, because the main place this is used
is delalloc, and any time we call btrfs_block_rsv_release() we do it
with qgroup_to_release set, and thus do the proper accounting.
The subvolume code is the only other code that uses the qgroup
reservation stuff, but it's intermingled with the above optimization,
and thus was getting its reservation freed out from underneath it and
thus leaking the reserved space.
The solution is to simply not mess with the qgroup reservations if we
don't have qgroup_to_release set. This works with the existing code as
anything that messes with the delalloc reservations always have
qgroup_to_release set. This fixes the leak that Boris was observing. |
| In the Linux kernel, the following vulnerability has been resolved:
net: core: remove unnecessary frame_sz check in bpf_xdp_adjust_tail()
Syzkaller reported the following issue:
=======================================
Too BIG xdp->frame_sz = 131072
WARNING: CPU: 0 PID: 5020 at net/core/filter.c:4121
____bpf_xdp_adjust_tail net/core/filter.c:4121 [inline]
WARNING: CPU: 0 PID: 5020 at net/core/filter.c:4121
bpf_xdp_adjust_tail+0x466/0xa10 net/core/filter.c:4103
...
Call Trace:
<TASK>
bpf_prog_4add87e5301a4105+0x1a/0x1c
__bpf_prog_run include/linux/filter.h:600 [inline]
bpf_prog_run_xdp include/linux/filter.h:775 [inline]
bpf_prog_run_generic_xdp+0x57e/0x11e0 net/core/dev.c:4721
netif_receive_generic_xdp net/core/dev.c:4807 [inline]
do_xdp_generic+0x35c/0x770 net/core/dev.c:4866
tun_get_user+0x2340/0x3ca0 drivers/net/tun.c:1919
tun_chr_write_iter+0xe8/0x210 drivers/net/tun.c:2043
call_write_iter include/linux/fs.h:1871 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x650/0xe40 fs/read_write.c:584
ksys_write+0x12f/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
xdp->frame_sz > PAGE_SIZE check was introduced in commit c8741e2bfe87
("xdp: Allow bpf_xdp_adjust_tail() to grow packet size"). But Jesper
Dangaard Brouer <jbrouer@redhat.com> noted that after introducing the
xdp_init_buff() which all XDP driver use - it's safe to remove this
check. The original intend was to catch cases where XDP drivers have
not been updated to use xdp.frame_sz, but that is not longer a concern
(since xdp_init_buff).
Running the initial syzkaller repro it was discovered that the
contiguous physical memory allocation is used for both xdp paths in
tun_get_user(), e.g. tun_build_skb() and tun_alloc_skb(). It was also
stated by Jesper Dangaard Brouer <jbrouer@redhat.com> that XDP can
work on higher order pages, as long as this is contiguous physical
memory (e.g. a page). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: core: Fix target_cmd_counter leak
The target_cmd_counter struct allocated via target_alloc_cmd_counter() is
never freed, resulting in leaks across various transport types, e.g.:
unreferenced object 0xffff88801f920120 (size 96):
comm "sh", pid 102, jiffies 4294892535 (age 713.412s)
hex dump (first 32 bytes):
07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 38 01 92 1f 80 88 ff ff ........8.......
backtrace:
[<00000000e58a6252>] kmalloc_trace+0x11/0x20
[<0000000043af4b2f>] target_alloc_cmd_counter+0x17/0x90 [target_core_mod]
[<000000007da2dfa7>] target_setup_session+0x2d/0x140 [target_core_mod]
[<0000000068feef86>] tcm_loop_tpg_nexus_store+0x19b/0x350 [tcm_loop]
[<000000006a80e021>] configfs_write_iter+0xb1/0x120
[<00000000e9f4d860>] vfs_write+0x2e4/0x3c0
[<000000008143433b>] ksys_write+0x80/0xb0
[<00000000a7df29b2>] do_syscall_64+0x42/0x90
[<0000000053f45fb8>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Free the structure alongside the corresponding iscsit_conn / se_sess
parent. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: turn quotas off if mount failed after enabling quotas
Yi found during a review of the patch "ext4: don't BUG on inconsistent
journal feature" that when ext4_mark_recovery_complete() returns an error
value, the error handling path does not turn off the enabled quotas,
which triggers the following kmemleak:
================================================================
unreferenced object 0xffff8cf68678e7c0 (size 64):
comm "mount", pid 746, jiffies 4294871231 (age 11.540s)
hex dump (first 32 bytes):
00 90 ef 82 f6 8c ff ff 00 00 00 00 41 01 00 00 ............A...
c7 00 00 00 bd 00 00 00 0a 00 00 00 48 00 00 00 ............H...
backtrace:
[<00000000c561ef24>] __kmem_cache_alloc_node+0x4d4/0x880
[<00000000d4e621d7>] kmalloc_trace+0x39/0x140
[<00000000837eee74>] v2_read_file_info+0x18a/0x3a0
[<0000000088f6c877>] dquot_load_quota_sb+0x2ed/0x770
[<00000000340a4782>] dquot_load_quota_inode+0xc6/0x1c0
[<0000000089a18bd5>] ext4_enable_quotas+0x17e/0x3a0 [ext4]
[<000000003a0268fa>] __ext4_fill_super+0x3448/0x3910 [ext4]
[<00000000b0f2a8a8>] ext4_fill_super+0x13d/0x340 [ext4]
[<000000004a9489c4>] get_tree_bdev+0x1dc/0x370
[<000000006e723bf1>] ext4_get_tree+0x1d/0x30 [ext4]
[<00000000c7cb663d>] vfs_get_tree+0x31/0x160
[<00000000320e1bed>] do_new_mount+0x1d5/0x480
[<00000000c074654c>] path_mount+0x22e/0xbe0
[<0000000003e97a8e>] do_mount+0x95/0xc0
[<000000002f3d3736>] __x64_sys_mount+0xc4/0x160
[<0000000027d2140c>] do_syscall_64+0x3f/0x90
================================================================
To solve this problem, we add a "failed_mount10" tag, and call
ext4_quota_off_umount() in this tag to release the enabled qoutas. |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: prevent deadlock by moving j1939_sk_errqueue()
This commit addresses a deadlock situation that can occur in certain
scenarios, such as when running data TP/ETP transfer and subscribing to
the error queue while receiving a net down event. The deadlock involves
locks in the following order:
3
j1939_session_list_lock -> active_session_list_lock
j1939_session_activate
...
j1939_sk_queue_activate_next -> sk_session_queue_lock
...
j1939_xtp_rx_eoma_one
2
j1939_sk_queue_drop_all -> sk_session_queue_lock
...
j1939_sk_netdev_event_netdown -> j1939_socks_lock
j1939_netdev_notify
1
j1939_sk_errqueue -> j1939_socks_lock
__j1939_session_cancel -> active_session_list_lock
j1939_tp_rxtimer
CPU0 CPU1
---- ----
lock(&priv->active_session_list_lock);
lock(&jsk->sk_session_queue_lock);
lock(&priv->active_session_list_lock);
lock(&priv->j1939_socks_lock);
The solution implemented in this commit is to move the
j1939_sk_errqueue() call out of the active_session_list_lock context,
thus preventing the deadlock situation. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: Fix system crash due to lack of free space in LFS
When f2fs tries to checkpoint during foreground gc in LFS mode, system
crash occurs due to lack of free space if the amount of dirty node and
dentry pages generated by data migration exceeds free space.
The reproduction sequence is as follows.
- 20GiB capacity block device (null_blk)
- format and mount with LFS mode
- create a file and write 20,000MiB
- 4k random write on full range of the file
RIP: 0010:new_curseg+0x48a/0x510 [f2fs]
Code: 55 e7 f5 89 c0 48 0f af c3 48 8b 5d c0 48 c1 e8 20 83 c0 01 89 43 6c 48 83 c4 28 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc <0f> 0b f0 41 80 4f 48 04 45 85 f6 0f 84 ba fd ff ff e9 ef fe ff ff
RSP: 0018:ffff977bc397b218 EFLAGS: 00010246
RAX: 00000000000027b9 RBX: 0000000000000000 RCX: 00000000000027c0
RDX: 0000000000000000 RSI: 00000000000027b9 RDI: ffff8c25ab4e74f8
RBP: ffff977bc397b268 R08: 00000000000027b9 R09: ffff8c29e4a34b40
R10: 0000000000000001 R11: ffff977bc397b0d8 R12: 0000000000000000
R13: ffff8c25b4dd81a0 R14: 0000000000000000 R15: ffff8c2f667f9000
FS: 0000000000000000(0000) GS:ffff8c344ec80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000c00055d000 CR3: 0000000e30810003 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
allocate_segment_by_default+0x9c/0x110 [f2fs]
f2fs_allocate_data_block+0x243/0xa30 [f2fs]
? __mod_lruvec_page_state+0xa0/0x150
do_write_page+0x80/0x160 [f2fs]
f2fs_do_write_node_page+0x32/0x50 [f2fs]
__write_node_page+0x339/0x730 [f2fs]
f2fs_sync_node_pages+0x5a6/0x780 [f2fs]
block_operations+0x257/0x340 [f2fs]
f2fs_write_checkpoint+0x102/0x1050 [f2fs]
f2fs_gc+0x27c/0x630 [f2fs]
? folio_mark_dirty+0x36/0x70
f2fs_balance_fs+0x16f/0x180 [f2fs]
This patch adds checking whether free sections are enough before checkpoint
during gc.
[Jaegeuk Kim: code clean-up] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix kernel warning during topology setup
This patch fixes the following kernel warning seen during
driver load by correctly initializing the p2plink attr before
creating the sysfs file:
[ +0.002865] ------------[ cut here ]------------
[ +0.002327] kobject: '(null)' (0000000056260cfb): is not initialized, yet kobject_put() is being called.
[ +0.004780] WARNING: CPU: 32 PID: 1006 at lib/kobject.c:718 kobject_put+0xaa/0x1c0
[ +0.001361] Call Trace:
[ +0.001234] <TASK>
[ +0.001067] kfd_remove_sysfs_node_entry+0x24a/0x2d0 [amdgpu]
[ +0.003147] kfd_topology_update_sysfs+0x3d/0x750 [amdgpu]
[ +0.002890] kfd_topology_add_device+0xbd7/0xc70 [amdgpu]
[ +0.002844] ? lock_release+0x13c/0x2e0
[ +0.001936] ? smu_cmn_send_smc_msg_with_param+0x1e8/0x2d0 [amdgpu]
[ +0.003313] ? amdgpu_dpm_get_mclk+0x54/0x60 [amdgpu]
[ +0.002703] kgd2kfd_device_init.cold+0x39f/0x4ed [amdgpu]
[ +0.002930] amdgpu_amdkfd_device_init+0x13d/0x1f0 [amdgpu]
[ +0.002944] amdgpu_device_init.cold+0x1464/0x17b4 [amdgpu]
[ +0.002970] ? pci_bus_read_config_word+0x43/0x80
[ +0.002380] amdgpu_driver_load_kms+0x15/0x100 [amdgpu]
[ +0.002744] amdgpu_pci_probe+0x147/0x370 [amdgpu]
[ +0.002522] local_pci_probe+0x40/0x80
[ +0.001896] work_for_cpu_fn+0x10/0x20
[ +0.001892] process_one_work+0x26e/0x5a0
[ +0.002029] worker_thread+0x1fd/0x3e0
[ +0.001890] ? process_one_work+0x5a0/0x5a0
[ +0.002115] kthread+0xea/0x110
[ +0.001618] ? kthread_complete_and_exit+0x20/0x20
[ +0.002422] ret_from_fork+0x1f/0x30
[ +0.001808] </TASK>
[ +0.001103] irq event stamp: 59837
[ +0.001718] hardirqs last enabled at (59849): [<ffffffffb30fab12>] __up_console_sem+0x52/0x60
[ +0.004414] hardirqs last disabled at (59860): [<ffffffffb30faaf7>] __up_console_sem+0x37/0x60
[ +0.004414] softirqs last enabled at (59654): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130
[ +0.004205] softirqs last disabled at (59649): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130
[ +0.004203] ---[ end trace 0000000000000000 ]--- |
