| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate the parameters of bo mapping operations more clearly
Verify the parameters of
amdgpu_vm_bo_(map/replace_map/clearing_mappings) in one common place. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: xilinx - call finalize with bh disabled
When calling crypto_finalize_request, BH should be disabled to avoid
triggering the following calltrace:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 74 at crypto/crypto_engine.c:58 crypto_finalize_request+0xa0/0x118
Modules linked in: cryptodev(O)
CPU: 2 PID: 74 Comm: firmware:zynqmp Tainted: G O 6.8.0-rc1-yocto-standard #323
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : crypto_finalize_request+0xa0/0x118
lr : crypto_finalize_request+0x104/0x118
sp : ffffffc085353ce0
x29: ffffffc085353ce0 x28: 0000000000000000 x27: ffffff8808ea8688
x26: ffffffc081715038 x25: 0000000000000000 x24: ffffff880100db00
x23: ffffff880100da80 x22: 0000000000000000 x21: 0000000000000000
x20: ffffff8805b14000 x19: ffffff880100da80 x18: 0000000000010450
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000003 x13: 0000000000000000 x12: ffffff880100dad0
x11: 0000000000000000 x10: ffffffc0832dcd08 x9 : ffffffc0812416d8
x8 : 00000000000001f4 x7 : ffffffc0830d2830 x6 : 0000000000000001
x5 : ffffffc082091000 x4 : ffffffc082091658 x3 : 0000000000000000
x2 : ffffffc7f9653000 x1 : 0000000000000000 x0 : ffffff8802d20000
Call trace:
crypto_finalize_request+0xa0/0x118
crypto_finalize_aead_request+0x18/0x30
zynqmp_handle_aes_req+0xcc/0x388
crypto_pump_work+0x168/0x2d8
kthread_worker_fn+0xfc/0x3a0
kthread+0x118/0x138
ret_from_fork+0x10/0x20
irq event stamp: 40
hardirqs last enabled at (39): [<ffffffc0812416f8>] _raw_spin_unlock_irqrestore+0x70/0xb0
hardirqs last disabled at (40): [<ffffffc08122d208>] el1_dbg+0x28/0x90
softirqs last enabled at (36): [<ffffffc080017dec>] kernel_neon_begin+0x8c/0xf0
softirqs last disabled at (34): [<ffffffc080017dc0>] kernel_neon_begin+0x60/0xf0
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: once more fix the call oder in amdgpu_ttm_move() v2
This reverts drm/amdgpu: fix ftrace event amdgpu_bo_move always move
on same heap. The basic problem here is that after the move the old
location is simply not available any more.
Some fixes were suggested, but essentially we should call the move
notification before actually moving things because only this way we have
the correct order for DMA-buf and VM move notifications as well.
Also rework the statistic handling so that we don't update the eviction
counter before the move.
v2: add missing NULL check |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: drop any code related to SCM_RIGHTS
This is dead code after we dropped support for passing io_uring fds
over SCM_RIGHTS, get rid of it. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: core: Fix unremoved procfs host directory regression
Commit fc663711b944 ("scsi: core: Remove the /proc/scsi/${proc_name}
directory earlier") fixed a bug related to modules loading/unloading, by
adding a call to scsi_proc_hostdir_rm() on scsi_remove_host(). But that led
to a potential duplicate call to the hostdir_rm() routine, since it's also
called from scsi_host_dev_release(). That triggered a regression report,
which was then fixed by commit be03df3d4bfe ("scsi: core: Fix a procfs host
directory removal regression"). The fix just dropped the hostdir_rm() call
from dev_release().
But it happens that this proc directory is created on scsi_host_alloc(),
and that function "pairs" with scsi_host_dev_release(), while
scsi_remove_host() pairs with scsi_add_host(). In other words, it seems the
reason for removing the proc directory on dev_release() was meant to cover
cases in which a SCSI host structure was allocated, but the call to
scsi_add_host() didn't happen. And that pattern happens to exist in some
error paths, for example.
Syzkaller causes that by using USB raw gadget device, error'ing on
usb-storage driver, at usb_stor_probe2(). By checking that path, we can see
that the BadDevice label leads to a scsi_host_put() after a SCSI host
allocation, but there's no call to scsi_add_host() in such path. That leads
to messages like this in dmesg (and a leak of the SCSI host proc
structure):
usb-storage 4-1:87.51: USB Mass Storage device detected
proc_dir_entry 'scsi/usb-storage' already registered
WARNING: CPU: 1 PID: 3519 at fs/proc/generic.c:377 proc_register+0x347/0x4e0 fs/proc/generic.c:376
The proper fix seems to still call scsi_proc_hostdir_rm() on dev_release(),
but guard that with the state check for SHOST_CREATED; there is even a
comment in scsi_host_dev_release() detailing that: such conditional is
meant for cases where the SCSI host was allocated but there was no calls to
{add,remove}_host(), like the usb-storage case.
This is what we propose here and with that, the error path of usb-storage
does not trigger the warning anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: check offset alignment in binder_get_object()
Commit 6d98eb95b450 ("binder: avoid potential data leakage when copying
txn") introduced changes to how binder objects are copied. In doing so,
it unintentionally removed an offset alignment check done through calls
to binder_alloc_copy_from_buffer() -> check_buffer().
These calls were replaced in binder_get_object() with copy_from_user(),
so now an explicit offset alignment check is needed here. This avoids
later complications when unwinding the objects gets harder.
It is worth noting this check existed prior to commit 7a67a39320df
("binder: add function to copy binder object from buffer"), likely
removed due to redundancy at the time. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-wmi-sysman: Fix WMI data block retrieval in sysfs callbacks
After retrieving WMI data blocks in sysfs callbacks, check for the
validity of them before dereferencing their content. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Stop parsing channels bits when all channels are found.
If a usb audio device sets more bits than the amount of channels
it could write outside of the map array. |
| In the Linux kernel, the following vulnerability has been resolved:
cpumap: Zero-initialise xdp_rxq_info struct before running XDP program
When running an XDP program that is attached to a cpumap entry, we don't
initialise the xdp_rxq_info data structure being used in the xdp_buff
that backs the XDP program invocation. Tobias noticed that this leads to
random values being returned as the xdp_md->rx_queue_index value for XDP
programs running in a cpumap.
This means we're basically returning the contents of the uninitialised
memory, which is bad. Fix this by zero-initialising the rxq data
structure before running the XDP program. |
| In the Linux kernel, the following vulnerability has been resolved:
NFC: nci: uart: Set tty->disc_data only in success path
Setting tty->disc_data before opening the NCI device means we need to
clean it up on error paths. This also opens some short window if device
starts sending data, even before NCIUARTSETDRIVER IOCTL succeeded
(broken hardware?). Close the window by exposing tty->disc_data only on
the success path, when opening of the NCI device and try_module_get()
succeeds.
The code differs in error path in one aspect: tty->disc_data won't be
ever assigned thus NULL-ified. This however should not be relevant
difference, because of "tty->disc_data=NULL" in nci_uart_tty_open(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: lan743x: Modify the EEPROM and OTP size for PCI1xxxx devices
Maximum OTP and EEPROM size for hearthstone PCI1xxxx devices are 8 Kb
and 64 Kb respectively. Adjust max size definitions and return correct
EEPROM length based on device. Also prevent out-of-bound read/write. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix sample vs do_exit()
Baisheng Gao reported an ARM64 crash, which Mark decoded as being a
synchronous external abort -- most likely due to trying to access
MMIO in bad ways.
The crash further shows perf trying to do a user stack sample while in
exit_mmap()'s tlb_finish_mmu() -- i.e. while tearing down the address
space it is trying to access.
It turns out that we stop perf after we tear down the userspace mm; a
receipie for disaster, since perf likes to access userspace for
various reasons.
Flip this order by moving up where we stop perf in do_exit().
Additionally, harden PERF_SAMPLE_CALLCHAIN and PERF_SAMPLE_STACK_USER
to abort when the current task does not have an mm (exit_mm() makes
sure to set current->mm = NULL; before commencing with the actual
teardown). Such that CPU wide events don't trip on this same problem. |
| In the Linux kernel, the following vulnerability has been resolved:
ubifs: Set page uptodate in the correct place
Page cache reads are lockless, so setting the freshly allocated page
uptodate before we've overwritten it with the data it's supposed to have
in it will allow a simultaneous reader to see old data. Move the call
to SetPageUptodate into ubifs_write_end(), which is after we copied the
new data into the page. |
| In the Linux kernel, the following vulnerability has been resolved:
pipe: wakeup wr_wait after setting max_usage
Commit c73be61cede5 ("pipe: Add general notification queue support") a
regression was introduced that would lock up resized pipes under certain
conditions. See the reproducer in [1].
The commit resizing the pipe ring size was moved to a different
function, doing that moved the wakeup for pipe->wr_wait before actually
raising pipe->max_usage. If a pipe was full before the resize occured it
would result in the wakeup never actually triggering pipe_write.
Set @max_usage and @nr_accounted before waking writers if this isn't a
watch queue.
[Christian Brauner <brauner@kernel.org>: rewrite to account for watch queues] |
| An issue was discovered in Wekan The Open Source kanban board system up to version 18.15, fixed in 18.16. Authorization flaw in card update handling allows board members (and potentially other authenticated users) to add/remove arbitrary user IDs in vote.positive / vote.negative arrays, enabling vote forgery and unauthorized voting. |
| SolarEdge SE3680HÂ ships with an outdated Linux kernel containing unpatched vulnerabilities in core subsystems. An attacker with network or local access can exploit these flaws to achieve remote code execution, privilege escalation, or disclosure of sensitive information. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix q->blkg_list corruption during disk rebind
Multiple gendisk instances can allocated/added for single request queue
in case of disk rebind. blkg may still stay in q->blkg_list when calling
blkcg_init_disk() for rebind, then q->blkg_list becomes corrupted.
Fix the list corruption issue by:
- add blkg_init_queue() to initialize q->blkg_list & q->blkcg_mutex only
- move calling blkg_init_queue() into blk_alloc_queue()
The list corruption should be started since commit f1c006f1c685 ("blk-cgroup:
synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()")
which delays removing blkg from q->blkg_list into blkg_free_workfn(). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix delayed allocation bug in ext4_clu_mapped for bigalloc + inline
When converting files with inline data to extents, delayed allocations
made on a file system created with both the bigalloc and inline options
can result in invalid extent status cache content, incorrect reserved
cluster counts, kernel memory leaks, and potential kernel panics.
With bigalloc, the code that determines whether a block must be
delayed allocated searches the extent tree to see if that block maps
to a previously allocated cluster. If not, the block is delayed
allocated, and otherwise, it isn't. However, if the inline option is
also used, and if the file containing the block is marked as able to
store data inline, there isn't a valid extent tree associated with
the file. The current code in ext4_clu_mapped() calls
ext4_find_extent() to search the non-existent tree for a previously
allocated cluster anyway, which typically finds nothing, as desired.
However, a side effect of the search can be to cache invalid content
from the non-existent tree (garbage) in the extent status tree,
including bogus entries in the pending reservation tree.
To fix this, avoid searching the extent tree when allocating blocks
for bigalloc + inline files that are being converted from inline to
extent mapped. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/64: Init jump labels before parse_early_param()
On 64-bit, calling jump_label_init() in setup_feature_keys() is too
late because static keys may be used in subroutines of
parse_early_param() which is again subroutine of early_init_devtree().
For example booting with "threadirqs":
static_key_enable_cpuslocked(): static key '0xc000000002953260' used before call to jump_label_init()
WARNING: CPU: 0 PID: 0 at kernel/jump_label.c:166 static_key_enable_cpuslocked+0xfc/0x120
...
NIP static_key_enable_cpuslocked+0xfc/0x120
LR static_key_enable_cpuslocked+0xf8/0x120
Call Trace:
static_key_enable_cpuslocked+0xf8/0x120 (unreliable)
static_key_enable+0x30/0x50
setup_forced_irqthreads+0x28/0x40
do_early_param+0xa0/0x108
parse_args+0x290/0x4e0
parse_early_options+0x48/0x5c
parse_early_param+0x58/0x84
early_init_devtree+0xd4/0x518
early_setup+0xb4/0x214
So call jump_label_init() just before parse_early_param() in
early_init_devtree().
[mpe: Add call trace to change log and minor wording edits.] |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Drop snd_BUG_ON() from snd_usbmidi_output_open()
snd_usbmidi_output_open() has a check of the NULL port with
snd_BUG_ON(). snd_BUG_ON() was used as this shouldn't have happened,
but in reality, the NULL port may be seen when the device gives an
invalid endpoint setup at the descriptor, hence the driver skips the
allocation. That is, the check itself is valid and snd_BUG_ON()
should be dropped from there. Otherwise it's confusing as if it were
a real bug, as recently syzbot stumbled on it. |
