| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: RX, Fix generating skb from non-linear xdp_buff for striding RQ
XDP programs can change the layout of an xdp_buff through
bpf_xdp_adjust_tail() and bpf_xdp_adjust_head(). Therefore, the driver
cannot assume the size of the linear data area nor fragments. Fix the
bug in mlx5 by generating skb according to xdp_buff after XDP programs
run.
Currently, when handling multi-buf XDP, the mlx5 driver assumes the
layout of an xdp_buff to be unchanged. That is, the linear data area
continues to be empty and fragments remain the same. This may cause
the driver to generate erroneous skb or triggering a kernel
warning. When an XDP program added linear data through
bpf_xdp_adjust_head(), the linear data will be ignored as
mlx5e_build_linear_skb() builds an skb without linear data and then
pull data from fragments to fill the linear data area. When an XDP
program has shrunk the non-linear data through bpf_xdp_adjust_tail(),
the delta passed to __pskb_pull_tail() may exceed the actual nonlinear
data size and trigger the BUG_ON in it.
To fix the issue, first record the original number of fragments. If the
number of fragments changes after the XDP program runs, rewind the end
fragment pointer by the difference and recalculate the truesize. Then,
build the skb with the linear data area matching the xdp_buff. Finally,
only pull data in if there is non-linear data and fill the linear part
up to 256 bytes. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/mellanox: mlxbf-pmc: add sysfs_attr_init() to count_clock init
The lock-related debug logic (CONFIG_LOCK_STAT) in the kernel is noting
the following warning when the BlueField-3 SOC is booted:
BUG: key ffff00008a3402a8 has not been registered!
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 4 PID: 592 at kernel/locking/lockdep.c:4801 lockdep_init_map_type+0x1d4/0x2a0
<snip>
Call trace:
lockdep_init_map_type+0x1d4/0x2a0
__kernfs_create_file+0x84/0x140
sysfs_add_file_mode_ns+0xcc/0x1cc
internal_create_group+0x110/0x3d4
internal_create_groups.part.0+0x54/0xcc
sysfs_create_groups+0x24/0x40
device_add+0x6e8/0x93c
device_register+0x28/0x40
__hwmon_device_register+0x4b0/0x8a0
devm_hwmon_device_register_with_groups+0x7c/0xe0
mlxbf_pmc_probe+0x1e8/0x3e0 [mlxbf_pmc]
platform_probe+0x70/0x110
The mlxbf_pmc driver must call sysfs_attr_init() during the
initialization of the "count_clock" data structure to avoid
this warning. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: rockchip-sfc: Fix DMA-API usage
Use DMA-API dma_map_single() call for getting the DMA address of the
transfer buffer instead of hacking with virt_to_phys().
This fixes the following DMA-API debug warning:
------------[ cut here ]------------
DMA-API: rockchip-sfc fe300000.spi: device driver tries to sync DMA memory it has not allocated [device address=0x000000000cf70000] [size=288 bytes]
WARNING: kernel/dma/debug.c:1106 at check_sync+0x1d8/0x690, CPU#2: systemd-udevd/151
Modules linked in: ...
Hardware name: Hardkernel ODROID-M1 (DT)
pstate: 604000c9 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : check_sync+0x1d8/0x690
lr : check_sync+0x1d8/0x690
..
Call trace:
check_sync+0x1d8/0x690 (P)
debug_dma_sync_single_for_cpu+0x84/0x8c
__dma_sync_single_for_cpu+0x88/0x234
rockchip_sfc_exec_mem_op+0x4a0/0x798 [spi_rockchip_sfc]
spi_mem_exec_op+0x408/0x498
spi_nor_read_data+0x170/0x184
spi_nor_read_sfdp+0x74/0xe4
spi_nor_parse_sfdp+0x120/0x11f0
spi_nor_sfdp_init_params_deprecated+0x3c/0x8c
spi_nor_scan+0x690/0xf88
spi_nor_probe+0xe4/0x304
spi_mem_probe+0x6c/0xa8
spi_probe+0x94/0xd4
really_probe+0xbc/0x298
... |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix double free of qgroup record after failure to add delayed ref head
In the previous code it was possible to incur into a double kfree()
scenario when calling add_delayed_ref_head(). This could happen if the
record was reported to already exist in the
btrfs_qgroup_trace_extent_nolock() call, but then there was an error
later on add_delayed_ref_head(). In this case, since
add_delayed_ref_head() returned an error, the caller went to free the
record. Since add_delayed_ref_head() couldn't set this kfree'd pointer
to NULL, then kfree() would have acted on a non-NULL 'record' object
which was pointing to memory already freed by the callee.
The problem comes from the fact that the responsibility to kfree the
object is on both the caller and the callee at the same time. Hence, the
fix for this is to shift the ownership of the 'qrecord' object out of
the add_delayed_ref_head(). That is, we will never attempt to kfree()
the given object inside of this function, and will expect the caller to
act on the 'qrecord' object on its own. The only exception where the
'qrecord' object cannot be kfree'd is if it was inserted into the
tracing logic, for which we already have the 'qrecord_inserted_ret'
boolean to account for this. Hence, the caller has to kfree the object
only if add_delayed_ref_head() reports not to have inserted it on the
tracing logic.
As a side-effect of the above, we must guarantee that
'qrecord_inserted_ret' is properly initialized at the start of the
function, not at the end, and then set when an actual insert
happens. This way we avoid 'qrecord_inserted_ret' having an invalid
value on an early exit.
The documentation from the add_delayed_ref_head() has also been updated
to reflect on the exact ownership of the 'qrecord' object. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: qmi_wwan: initialize MAC header offset in qmimux_rx_fixup
Raw IP packets have no MAC header, leaving skb->mac_header uninitialized.
This can trigger kernel panics on ARM64 when xfrm or other subsystems
access the offset due to strict alignment checks.
Initialize the MAC header to prevent such crashes.
This can trigger kernel panics on ARM when running IPsec over the
qmimux0 interface.
Example trace:
Internal error: Oops: 000000009600004f [#1] SMP
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.34-gbe78e49cb433 #1
Hardware name: LS1028A RDB Board (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : xfrm_input+0xde8/0x1318
lr : xfrm_input+0x61c/0x1318
sp : ffff800080003b20
Call trace:
xfrm_input+0xde8/0x1318
xfrm6_rcv+0x38/0x44
xfrm6_esp_rcv+0x48/0xa8
ip6_protocol_deliver_rcu+0x94/0x4b0
ip6_input_finish+0x44/0x70
ip6_input+0x44/0xc0
ipv6_rcv+0x6c/0x114
__netif_receive_skb_one_core+0x5c/0x8c
__netif_receive_skb+0x18/0x60
process_backlog+0x78/0x17c
__napi_poll+0x38/0x180
net_rx_action+0x168/0x2f0 |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-fc: avoid scheduling association deletion twice
When forcefully shutting down a port via the configfs interface,
nvmet_port_subsys_drop_link() first calls nvmet_port_del_ctrls() and
then nvmet_disable_port(). Both functions will eventually schedule all
remaining associations for deletion.
The current implementation checks whether an association is about to be
removed, but only after the work item has already been scheduled. As a
result, it is possible for the first scheduled work item to free all
resources, and then for the same work item to be scheduled again for
deletion.
Because the association list is an RCU list, it is not possible to take
a lock and remove the list entry directly, so it cannot be looked up
again. Instead, a flag (terminating) must be used to determine whether
the association is already in the process of being deleted. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Define actions for the new time_deleg FATTR4 attributes
NFSv4 clients won't send legitimate GETATTR requests for these new
attributes because they are intended to be used only with CB_GETATTR
and SETATTR. But NFSD has to do something besides crashing if it
ever sees a GETATTR request that queries these attributes.
RFC 8881 Section 18.7.3 states:
> The server MUST return a value for each attribute that the client
> requests if the attribute is supported by the server for the
> target file system. If the server does not support a particular
> attribute on the target file system, then it MUST NOT return the
> attribute value and MUST NOT set the attribute bit in the result
> bitmap. The server MUST return an error if it supports an
> attribute on the target but cannot obtain its value. In that case,
> no attribute values will be returned.
Further, RFC 9754 Section 5 states:
> These new attributes are invalid to be used with GETATTR, VERIFY,
> and NVERIFY, and they can only be used with CB_GETATTR and SETATTR
> by a client holding an appropriate delegation.
Thus there does not appear to be a specific server response mandated
by specification. Taking the guidance that querying these attributes
via GETATTR is "invalid", NFSD will return nfserr_inval, failing the
request entirely. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/secretmem: fix use-after-free race in fault handler
When a page fault occurs in a secret memory file created with
`memfd_secret(2)`, the kernel will allocate a new folio for it, mark the
underlying page as not-present in the direct map, and add it to the file
mapping.
If two tasks cause a fault in the same page concurrently, both could end
up allocating a folio and removing the page from the direct map, but only
one would succeed in adding the folio to the file mapping. The task that
failed undoes the effects of its attempt by (a) freeing the folio again
and (b) putting the page back into the direct map. However, by doing
these two operations in this order, the page becomes available to the
allocator again before it is placed back in the direct mapping.
If another task attempts to allocate the page between (a) and (b), and the
kernel tries to access it via the direct map, it would result in a
supervisor not-present page fault.
Fix the ordering to restore the direct map before the folio is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: also call xfrm_state_delete_tunnel at destroy time for states that were never added
In commit b441cf3f8c4b ("xfrm: delete x->tunnel as we delete x"), I
missed the case where state creation fails between full
initialization (->init_state has been called) and being inserted on
the lists.
In this situation, ->init_state has been called, so for IPcomp
tunnels, the fallback tunnel has been created and added onto the
lists, but the user state never gets added, because we fail before
that. The user state doesn't go through __xfrm_state_delete, so we
don't call xfrm_state_delete_tunnel for those states, and we end up
leaking the FB tunnel.
There are several codepaths affected by this: the add/update paths, in
both net/key and xfrm, and the migrate code (xfrm_migrate,
xfrm_state_migrate). A "proper" rollback of the init_state work would
probably be doable in the add/update code, but for migrate it gets
more complicated as multiple states may be involved.
At some point, the new (not-inserted) state will be destroyed, so call
xfrm_state_delete_tunnel during xfrm_state_gc_destroy. Most states
will have their fallback tunnel cleaned up during __xfrm_state_delete,
which solves the issue that b441cf3f8c4b (and other patches before it)
aimed at. All states (including FB tunnels) will be removed from the
lists once xfrm_state_fini has called flush_work(&xfrm_state_gc_work). |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: fix module removal if firmware download failed
Fix remove if firmware failed to load:
qcom-iris aa00000.video-codec: Direct firmware load for qcom/vpu/vpu33_p4.mbn failed with error -2
qcom-iris aa00000.video-codec: firmware download failed
qcom-iris aa00000.video-codec: core init failed
then:
$ echo aa00000.video-codec > /sys/bus/platform/drivers/qcom-iris/unbind
Triggers:
genpd genpd:1:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
video_cc_mvs0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#1: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
video_cc_mvs0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#2: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
genpd genpd:0:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
gcc_video_axi0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#4: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
------------[ cut here ]------------
gcc_video_axi0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#4: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
Skip deinit if initialization never succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix metadata_dst leak __bpf_redirect_neigh_v{4,6}
Cilium has a BPF egress gateway feature which forces outgoing K8s Pod
traffic to pass through dedicated egress gateways which then SNAT the
traffic in order to interact with stable IPs outside the cluster.
The traffic is directed to the gateway via vxlan tunnel in collect md
mode. A recent BPF change utilized the bpf_redirect_neigh() helper to
forward packets after the arrival and decap on vxlan, which turned out
over time that the kmalloc-256 slab usage in kernel was ever-increasing.
The issue was that vxlan allocates the metadata_dst object and attaches
it through a fake dst entry to the skb. The latter was never released
though given bpf_redirect_neigh() was merely setting the new dst entry
via skb_dst_set() without dropping an existing one first. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: BPF: No support of struct argument in trampoline programs
The current implementation does not support struct argument. This causes
a oops when running bpf selftest:
$ ./test_progs -a tracing_struct
Oops[#1]:
CPU -1 Unable to handle kernel paging request at virtual address 0000000000000018, era == 9000000085bef268, ra == 90000000844f3938
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 1-...0: (19 ticks this GP) idle=1094/1/0x4000000000000000 softirq=1380/1382 fqs=801
rcu: (detected by 0, t=5252 jiffies, g=1197, q=52 ncpus=4)
Sending NMI from CPU 0 to CPUs 1:
rcu: rcu_preempt kthread starved for 2495 jiffies! g1197 f0x0 RCU_GP_DOING_FQS(6) ->state=0x0 ->cpu=2
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 task_flags:0x208040 flags:0x00000800
Stack : 9000000100423e80 0000000000000402 0000000000000010 90000001003b0680
9000000085d88000 0000000000000000 0000000000000040 9000000087159350
9000000085c2b9b0 0000000000000001 900000008704a000 0000000000000005
00000000ffff355b 00000000ffff355b 0000000000000000 0000000000000004
9000000085d90510 0000000000000000 0000000000000002 7b5d998f8281e86e
00000000ffff355c 7b5d998f8281e86e 000000000000003f 9000000087159350
900000008715bf98 0000000000000005 9000000087036000 900000008704a000
9000000100407c98 90000001003aff80 900000008715c4c0 9000000085c2b9b0
00000000ffff355b 9000000085c33d3c 00000000000000b4 0000000000000000
9000000007002150 00000000ffff355b 9000000084615480 0000000007000002
...
Call Trace:
[<9000000085c2a868>] __schedule+0x410/0x1520
[<9000000085c2b9ac>] schedule+0x34/0x190
[<9000000085c33d38>] schedule_timeout+0x98/0x140
[<90000000845e9120>] rcu_gp_fqs_loop+0x5f8/0x868
[<90000000845ed538>] rcu_gp_kthread+0x260/0x2e0
[<900000008454e8a4>] kthread+0x144/0x238
[<9000000085c26b60>] ret_from_kernel_thread+0x28/0xc8
[<90000000844f20e4>] ret_from_kernel_thread_asm+0xc/0x88
rcu: Stack dump where RCU GP kthread last ran:
Sending NMI from CPU 0 to CPUs 2:
NMI backtrace for cpu 2 skipped: idling at idle_exit+0x0/0x4
Reject it for now. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid NULL pointer dereference in f2fs_check_quota_consistency()
syzbot reported a f2fs bug as below:
Oops: gen[ 107.736417][ T5848] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 UID: 0 PID: 5848 Comm: syz-executor263 Tainted: G W 6.17.0-rc1-syzkaller-00014-g0e39a731820a #0 PREEMPT_{RT,(full)}
RIP: 0010:strcmp+0x3c/0xc0 lib/string.c:284
Call Trace:
<TASK>
f2fs_check_quota_consistency fs/f2fs/super.c:1188 [inline]
f2fs_check_opt_consistency+0x1378/0x2c10 fs/f2fs/super.c:1436
__f2fs_remount fs/f2fs/super.c:2653 [inline]
f2fs_reconfigure+0x482/0x1770 fs/f2fs/super.c:5297
reconfigure_super+0x224/0x890 fs/super.c:1077
do_remount fs/namespace.c:3314 [inline]
path_mount+0xd18/0xfe0 fs/namespace.c:4112
do_mount fs/namespace.c:4133 [inline]
__do_sys_mount fs/namespace.c:4344 [inline]
__se_sys_mount+0x317/0x410 fs/namespace.c:4321
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The direct reason is f2fs_check_quota_consistency() may suffer null-ptr-deref
issue in strcmp().
The bug can be reproduced w/ below scripts:
mkfs.f2fs -f /dev/vdb
mount -t f2fs -o usrquota /dev/vdb /mnt/f2fs
quotacheck -uc /mnt/f2fs/
umount /mnt/f2fs
mount -t f2fs -o usrjquota=aquota.user,jqfmt=vfsold /dev/vdb /mnt/f2fs
mount -t f2fs -o remount,usrjquota=,jqfmt=vfsold /dev/vdb /mnt/f2fs
umount /mnt/f2fs
So, before old_qname and new_qname comparison, we need to check whether
they are all valid pointers, fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm80xx: Fix array-index-out-of-of-bounds on rmmod
Since commit f7b705c238d1 ("scsi: pm80xx: Set phy_attached to zero when
device is gone") UBSAN reports:
UBSAN: array-index-out-of-bounds in drivers/scsi/pm8001/pm8001_sas.c:786:17
index 28 is out of range for type 'pm8001_phy [16]'
on rmmod when using an expander.
For a direct attached device, attached_phy contains the local phy id.
For a device behind an expander, attached_phy contains the remote phy
id, not the local phy id.
I.e. while pm8001_ha will have pm8001_ha->chip->n_phy local phys, for a
device behind an expander, attached_phy can be much larger than
pm8001_ha->chip->n_phy (depending on the amount of phys of the
expander).
E.g. on my system pm8001_ha has 8 phys with phy ids 0-7. One of the
ports has an expander connected. The expander has 31 phys with phy ids
0-30.
The pm8001_ha->phy array only contains the phys of the HBA. It does not
contain the phys of the expander. Thus, it is wrong to use attached_phy
to index the pm8001_ha->phy array for a device behind an expander.
Thus, we can only clear phy_attached for devices that are directly
attached. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_acm: Refactor bind path to use __free()
After an bind/unbind cycle, the acm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
gs_free_req+0x30/0x44
acm_bind+0x1b8/0x1f4
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix double-free in dbitmap
A process might fail to allocate a new bitmap when trying to expand its
proc->dmap. In that case, dbitmap_grow() fails and frees the old bitmap
via dbitmap_free(). However, the driver calls dbitmap_free() again when
the same process terminates, leading to a double-free error:
==================================================================
BUG: KASAN: double-free in binder_proc_dec_tmpref+0x2e0/0x55c
Free of addr ffff00000b7c1420 by task kworker/9:1/209
CPU: 9 UID: 0 PID: 209 Comm: kworker/9:1 Not tainted 6.17.0-rc6-dirty #5 PREEMPT
Hardware name: linux,dummy-virt (DT)
Workqueue: events binder_deferred_func
Call trace:
kfree+0x164/0x31c
binder_proc_dec_tmpref+0x2e0/0x55c
binder_deferred_func+0xc24/0x1120
process_one_work+0x520/0xba4
[...]
Allocated by task 448:
__kmalloc_noprof+0x178/0x3c0
bitmap_zalloc+0x24/0x30
binder_open+0x14c/0xc10
[...]
Freed by task 449:
kfree+0x184/0x31c
binder_inc_ref_for_node+0xb44/0xe44
binder_transaction+0x29b4/0x7fbc
binder_thread_write+0x1708/0x442c
binder_ioctl+0x1b50/0x2900
[...]
==================================================================
Fix this issue by marking proc->map NULL in dbitmap_free(). |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix KASAN global-out-of-bounds warning
When running "perf mem record" command on CWF, the below KASAN
global-out-of-bounds warning is seen.
==================================================================
BUG: KASAN: global-out-of-bounds in cmt_latency_data+0x176/0x1b0
Read of size 4 at addr ffffffffb721d000 by task dtlb/9850
Call Trace:
kasan_report+0xb8/0xf0
cmt_latency_data+0x176/0x1b0
setup_arch_pebs_sample_data+0xf49/0x2560
intel_pmu_drain_arch_pebs+0x577/0xb00
handle_pmi_common+0x6c4/0xc80
The issue is caused by below code in __grt_latency_data(). The code
tries to access x86_hybrid_pmu structure which doesn't exist on
non-hybrid platform like CWF.
WARN_ON_ONCE(hybrid_pmu(event->pmu)->pmu_type == hybrid_big)
So add is_hybrid() check before calling this WARN_ON_ONCE to fix the
global-out-of-bounds access issue. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix multifs mds auth caps issue
The mds auth caps check should also validate the
fsname along with the associated caps. Not doing
so would result in applying the mds auth caps of
one fs on to the other fs in a multifs ceph cluster.
The bug causes multiple issues w.r.t user
authentication, following is one such example.
Steps to Reproduce (on vstart cluster):
1. Create two file systems in a cluster, say 'fsname1' and 'fsname2'
2. Authorize read only permission to the user 'client.usr' on fs 'fsname1'
$ceph fs authorize fsname1 client.usr / r
3. Authorize read and write permission to the same user 'client.usr' on fs 'fsname2'
$ceph fs authorize fsname2 client.usr / rw
4. Update the keyring
$ceph auth get client.usr >> ./keyring
With above permssions for the user 'client.usr', following is the
expectation.
a. The 'client.usr' should be able to only read the contents
and not allowed to create or delete files on file system 'fsname1'.
b. The 'client.usr' should be able to read/write on file system 'fsname2'.
But, with this bug, the 'client.usr' is allowed to read/write on file
system 'fsname1'. See below.
5. Mount the file system 'fsname1' with the user 'client.usr'
$sudo bin/mount.ceph usr@.fsname1=/ /kmnt_fsname1_usr/
6. Try creating a file on file system 'fsname1' with user 'client.usr'. This
should fail but passes with this bug.
$touch /kmnt_fsname1_usr/file1
7. Mount the file system 'fsname1' with the user 'client.admin' and create a
file.
$sudo bin/mount.ceph admin@.fsname1=/ /kmnt_fsname1_admin
$echo "data" > /kmnt_fsname1_admin/admin_file1
8. Try removing an existing file on file system 'fsname1' with the user
'client.usr'. This shoudn't succeed but succeeds with the bug.
$rm -f /kmnt_fsname1_usr/admin_file1
For more information, please take a look at the corresponding mds/fuse patch
and tests added by looking into the tracker mentioned below.
v2: Fix a possible null dereference in doutc
v3: Don't store fsname from mdsmap, validate against
ceph_mount_options's fsname and use it
v4: Code refactor, better warning message and
fix possible compiler warning
[ Slava.Dubeyko: "fsname check failed" -> "fsname mismatch" ] |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: check device's attached status in compat ioctls
Syzbot identified an issue [1] that crashes kernel, seemingly due to
unexistent callback dev->get_valid_routes(). By all means, this should
not occur as said callback must always be set to
get_zero_valid_routes() in __comedi_device_postconfig().
As the crash seems to appear exclusively in i386 kernels, at least,
judging from [1] reports, the blame lies with compat versions
of standard IOCTL handlers. Several of them are modified and
do not use comedi_unlocked_ioctl(). While functionality of these
ioctls essentially copy their original versions, they do not
have required sanity check for device's attached status. This,
in turn, leads to a possibility of calling select IOCTLs on a
device that has not been properly setup, even via COMEDI_DEVCONFIG.
Doing so on unconfigured devices means that several crucial steps
are missed, for instance, specifying dev->get_valid_routes()
callback.
Fix this somewhat crudely by ensuring device's attached status before
performing any ioctls, improving logic consistency between modern
and compat functions.
[1] Syzbot report:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
CR2: ffffffffffffffd6 CR3: 000000006c717000 CR4: 0000000000352ef0
Call Trace:
<TASK>
get_valid_routes drivers/comedi/comedi_fops.c:1322 [inline]
parse_insn+0x78c/0x1970 drivers/comedi/comedi_fops.c:1401
do_insnlist_ioctl+0x272/0x700 drivers/comedi/comedi_fops.c:1594
compat_insnlist drivers/comedi/comedi_fops.c:3208 [inline]
comedi_compat_ioctl+0x810/0x990 drivers/comedi/comedi_fops.c:3273
__do_compat_sys_ioctl fs/ioctl.c:695 [inline]
__se_compat_sys_ioctl fs/ioctl.c:638 [inline]
__ia32_compat_sys_ioctl+0x242/0x370 fs/ioctl.c:638
do_syscall_32_irqs_on arch/x86/entry/syscall_32.c:83 [inline]
... |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: multiq3: sanitize config options in multiq3_attach()
Syzbot identified an issue [1] in multiq3_attach() that induces a
task timeout due to open() or COMEDI_DEVCONFIG ioctl operations,
specifically, in the case of multiq3 driver.
This problem arose when syzkaller managed to craft weird configuration
options used to specify the number of channels in encoder subdevice.
If a particularly great number is passed to s->n_chan in
multiq3_attach() via it->options[2], then multiple calls to
multiq3_encoder_reset() at the end of driver-specific attach() method
will be running for minutes, thus blocking tasks and affected devices
as well.
While this issue is most likely not too dangerous for real-life
devices, it still makes sense to sanitize configuration inputs. Enable
a sensible limit on the number of encoder chips (4 chips max, each
with 2 channels) to stop this behaviour from manifesting.
[1] Syzbot crash:
INFO: task syz.2.19:6067 blocked for more than 143 seconds.
...
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5254 [inline]
__schedule+0x17c4/0x4d60 kernel/sched/core.c:6862
__schedule_loop kernel/sched/core.c:6944 [inline]
schedule+0x165/0x360 kernel/sched/core.c:6959
schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:7016
__mutex_lock_common kernel/locking/mutex.c:676 [inline]
__mutex_lock+0x7e6/0x1350 kernel/locking/mutex.c:760
comedi_open+0xc0/0x590 drivers/comedi/comedi_fops.c:2868
chrdev_open+0x4cc/0x5e0 fs/char_dev.c:414
do_dentry_open+0x953/0x13f0 fs/open.c:965
vfs_open+0x3b/0x340 fs/open.c:1097
... |
