| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_open/close(): fix memory leak
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the 928150fad41b ("can: esd_usb2: fix memory
leak"). |
| radare2 v5.9.8 and before contains a memory leak in the function bochs_open. |
| radare2 v5.9.8 and before contains a memory leak in the function r2r_subprocess_init. |
| radare2 v5.9.8 and before contains a memory leak in the function r_bin_object_new. |
| radare2 v.5.9.8 and before contains a memory leak in the function _load_relocations. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix insufficient bounds propagation from adjust_scalar_min_max_vals
Kuee reported a corner case where the tnum becomes constant after the call
to __reg_bound_offset(), but the register's bounds are not, that is, its
min bounds are still not equal to the register's max bounds.
This in turn allows to leak pointers through turning a pointer register as
is into an unknown scalar via adjust_ptr_min_max_vals().
Before:
func#0 @0
0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0))
1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0))
2: (87) r3 = -r3 ; R3_w=scalar()
3: (87) r3 = -r3 ; R3_w=scalar()
4: (47) r3 |= 32767 ; R3_w=scalar(smin=-9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-2147450881)
5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
6: (95) exit
from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
8: (95) exit
from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
9: (07) r3 += -32767 ; R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)) <--- [*]
10: (95) exit
What can be seen here is that R3=scalar(umin=32767,umax=32768,var_off=(0x7fff;
0x8000)) after the operation R3 += -32767 results in a 'malformed' constant, that
is, R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)). Intersecting with var_off has
not been done at that point via __update_reg_bounds(), which would have improved
the umax to be equal to umin.
Refactor the tnum <> min/max bounds information flow into a reg_bounds_sync()
helper and use it consistently everywhere. After the fix, bounds have been
corrected to R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) and thus the register
is regarded as a 'proper' constant scalar of 0.
After:
func#0 @0
0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0))
1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0))
2: (87) r3 = -r3 ; R3_w=scalar()
3: (87) r3 = -r3 ; R3_w=scalar()
4: (47) r3 |= 32767 ; R3_w=scalar(smin=-9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-2147450881)
5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
6: (95) exit
from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
8: (95) exit
from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix leaks in probe
These two error paths should clean up before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/papr_scm: Fix leaking nvdimm_events_map elements
Right now 'char *' elements allocated for individual 'stat_id' in
'papr_scm_priv.nvdimm_events_map[]' during papr_scm_pmu_check_events(), get
leaked in papr_scm_remove() and papr_scm_pmu_register(),
papr_scm_pmu_check_events() error paths.
Also individual 'stat_id' arent NULL terminated 'char *' instead they are fixed
8-byte sized identifiers. However papr_scm_pmu_register() assumes it to be a
NULL terminated 'char *' and at other places it assumes it to be a
'papr_scm_perf_stat.stat_id' sized string which is 8-byes in size.
Fix this by allocating the memory for papr_scm_priv.nvdimm_events_map to also
include space for 'stat_id' entries. This is possible since number of available
events/stat_ids are known upfront. This saves some memory and one extra level of
indirection from 'nvdimm_events_map' to 'stat_id'. Also rest of the code
can continue to call 'kfree(papr_scm_priv.nvdimm_events_map)' without needing to
iterate over the array and free up individual elements. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers/base/node.c: fix compaction sysfs file leak
Compaction sysfs file is created via compaction_register_node in
register_node. But we forgot to remove it in unregister_node. Thus
compaction sysfs file is leaked. Using compaction_unregister_node to fix
this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix anon_dev leak in create_subvol()
When btrfs_qgroup_inherit(), btrfs_alloc_tree_block, or
btrfs_insert_root() fail in create_subvol(), we return without freeing
anon_dev. Reorganize the error handling in create_subvol() to fix this. |
| In the Linux kernel, the following vulnerability has been resolved:
rtw89: ser: fix CAM leaks occurring in L2 reset
The CAM, meaning address CAM and bssid CAM here, will get leaks during
SER (system error recover) L2 reset process and ieee80211_restart_hw()
which is called by L2 reset process eventually.
The normal flow would be like
-> add interface (acquire 1)
-> enter ips (release 1)
-> leave ips (acquire 1)
-> connection (occupy 1) <(A) 1 leak after L2 reset if non-sec connection>
The ieee80211_restart_hw() flow (under connection)
-> ieee80211 reconfig
-> add interface (acquire 1)
-> leave ips (acquire 1)
-> connection (occupy (A) + 2) <(B) 1 more leak>
Originally, CAM is released before HW restart only if connection is under
security. Now, release CAM whatever connection it is to fix leak in (A).
OTOH, check if CAM is already valid to avoid acquiring multiple times to
fix (B).
Besides, if AP mode, release address CAM of all stations before HW restart. |
| When SNMP v1 or v2c are disabled on the BIG-IP, undisclosed requests can cause an increase in memory resource utilization.
Note: Software versions which have reached End of Technical Support (EoTS) are not evaluated |
| in OpenHarmony v5.0.2 and prior versions allow a local attacker case DOS through missing release of memory. |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: Free skb when TX metadata options are invalid
When a new skb is allocated for transmitting an xsk descriptor, i.e., for
every non-multibuf descriptor or the first frag of a multibuf descriptor,
but the descriptor is later found to have invalid options set for the TX
metadata, the new skb is never freed. This can leak skbs until the send
buffer is full which makes sending more packets impossible.
Fix this by freeing the skb in the error path if we are currently dealing
with the first frag, i.e., an skb allocated in this iteration of
xsk_build_skb. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: Fix sk_error_queue memory leak
Kernel queues MSG_ZEROCOPY completion notifications on the error queue.
Where they remain, until explicitly recv()ed. To prevent memory leaks,
clean up the queue when the socket is destroyed.
unreferenced object 0xffff8881028beb00 (size 224):
comm "vsock_test", pid 1218, jiffies 4294694897
hex dump (first 32 bytes):
90 b0 21 17 81 88 ff ff 90 b0 21 17 81 88 ff ff ..!.......!.....
00 00 00 00 00 00 00 00 00 b0 21 17 81 88 ff ff ..........!.....
backtrace (crc 6c7031ca):
[<ffffffff81418ef7>] kmem_cache_alloc_node_noprof+0x2f7/0x370
[<ffffffff81d35882>] __alloc_skb+0x132/0x180
[<ffffffff81d2d32b>] sock_omalloc+0x4b/0x80
[<ffffffff81d3a8ae>] msg_zerocopy_realloc+0x9e/0x240
[<ffffffff81fe5cb2>] virtio_transport_send_pkt_info+0x412/0x4c0
[<ffffffff81fe6183>] virtio_transport_stream_enqueue+0x43/0x50
[<ffffffff81fe0813>] vsock_connectible_sendmsg+0x373/0x450
[<ffffffff81d233d5>] ____sys_sendmsg+0x365/0x3a0
[<ffffffff81d246f4>] ___sys_sendmsg+0x84/0xd0
[<ffffffff81d26f47>] __sys_sendmsg+0x47/0x80
[<ffffffff820d3df3>] do_syscall_64+0x93/0x180
[<ffffffff8220012b>] entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
virtio/vsock: Improve MSG_ZEROCOPY error handling
Add a missing kfree_skb() to prevent memory leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Fix possible exec queue leak in exec IOCTL
In a couple of places after an exec queue is looked up the exec IOCTL
returns on input errors without dropping the exec queue ref. Fix this
ensuring the exec queue ref is dropped on input error.
(cherry picked from commit 07064a200b40ac2195cb6b7b779897d9377e5e6f) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/imagination: Break an object reference loop
When remaining resources are being cleaned up on driver close,
outstanding VM mappings may result in resources being leaked, due
to an object reference loop, as shown below, with each object (or
set of objects) referencing the object below it:
PVR GEM Object
GPU scheduler "finished" fence
GPU scheduler “scheduled” fence
PVR driver “done” fence
PVR Context
PVR VM Context
PVR VM Mappings
PVR GEM Object
The reference that the PVR VM Context has on the VM mappings is a
soft one, in the sense that the freeing of outstanding VM mappings
is done as part of VM context destruction; no reference counts are
involved, as is the case for all the other references in the loop.
To break the reference loop during cleanup, free the outstanding
VM mappings before destroying the PVR Context associated with the
VM context. |
| In the Linux kernel, the following vulnerability has been resolved:
rpcrdma: Always release the rpcrdma_device's xa_array
Dai pointed out that the xa_init_flags() in rpcrdma_add_one() needs
to have a matching xa_destroy() in rpcrdma_remove_one() to release
underlying memory that the xarray might have accrued during
operation. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Free dynamically allocated bits in bpf_iter_bits_destroy()
bpf_iter_bits_destroy() uses "kit->nr_bits <= 64" to check whether the
bits are dynamically allocated. However, the check is incorrect and may
cause a kmemleak as shown below:
unreferenced object 0xffff88812628c8c0 (size 32):
comm "swapper/0", pid 1, jiffies 4294727320
hex dump (first 32 bytes):
b0 c1 55 f5 81 88 ff ff f0 f0 f0 f0 f0 f0 f0 f0 ..U...........
f0 f0 f0 f0 f0 f0 f0 f0 00 00 00 00 00 00 00 00 ..............
backtrace (crc 781e32cc):
[<00000000c452b4ab>] kmemleak_alloc+0x4b/0x80
[<0000000004e09f80>] __kmalloc_node_noprof+0x480/0x5c0
[<00000000597124d6>] __alloc.isra.0+0x89/0xb0
[<000000004ebfffcd>] alloc_bulk+0x2af/0x720
[<00000000d9c10145>] prefill_mem_cache+0x7f/0xb0
[<00000000ff9738ff>] bpf_mem_alloc_init+0x3e2/0x610
[<000000008b616eac>] bpf_global_ma_init+0x19/0x30
[<00000000fc473efc>] do_one_initcall+0xd3/0x3c0
[<00000000ec81498c>] kernel_init_freeable+0x66a/0x940
[<00000000b119f72f>] kernel_init+0x20/0x160
[<00000000f11ac9a7>] ret_from_fork+0x3c/0x70
[<0000000004671da4>] ret_from_fork_asm+0x1a/0x30
That is because nr_bits will be set as zero in bpf_iter_bits_next()
after all bits have been iterated.
Fix the issue by setting kit->bit to kit->nr_bits instead of setting
kit->nr_bits to zero when the iteration completes in
bpf_iter_bits_next(). In addition, use "!nr_bits || bits >= nr_bits" to
check whether the iteration is complete and still use "nr_bits > 64" to
indicate whether bits are dynamically allocated. The "!nr_bits" check is
necessary because bpf_iter_bits_new() may fail before setting
kit->nr_bits, and this condition will stop the iteration early instead
of accessing the zeroed or freed kit->bits.
Considering the initial value of kit->bits is -1 and the type of
kit->nr_bits is unsigned int, change the type of kit->nr_bits to int.
The potential overflow problem will be handled in the following patch. |
