Export limit exceeded: 36326 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (36326 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-7697 | 2 Tecno, Transsion | 2 Com.transsion.carlcare, Carlcare | 2025-11-13 | 7.5 High |
| Logical vulnerability in the mobile application (com.transsion.carlcare) may lead to user information leakage risks. | ||||
| CVE-2025-37815 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: misc: microchip: pci1xxxx: Fix Kernel panic during IRQ handler registration Resolve kernel panic while accessing IRQ handler associated with the generated IRQ. This is done by acquiring the spinlock and storing the current interrupt state before handling the interrupt request using generic_handle_irq. A previous fix patch was submitted where 'generic_handle_irq' was replaced with 'handle_nested_irq'. However, this change also causes the kernel panic where after determining which GPIO triggered the interrupt and attempting to call handle_nested_irq with the mapped IRQ number, leads to a failure in locating the registered handler. | ||||
| CVE-2025-37816 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mei: vsc: Fix fortify-panic caused by invalid counted_by() use gcc 15 honors the __counted_by(len) attribute on vsc_tp_packet.buf[] and the vsc-tp.c code is using this in a wrong way. len does not contain the available size in the buffer, it contains the actual packet length *without* the crc. So as soon as vsc_tp_xfer() tries to add the crc to buf[] the fortify-panic handler gets triggered: [ 80.842193] memcpy: detected buffer overflow: 4 byte write of buffer size 0 [ 80.842243] WARNING: CPU: 4 PID: 272 at lib/string_helpers.c:1032 __fortify_report+0x45/0x50 ... [ 80.843175] __fortify_panic+0x9/0xb [ 80.843186] vsc_tp_xfer.cold+0x67/0x67 [mei_vsc_hw] [ 80.843210] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90 [ 80.843229] ? lockdep_hardirqs_on+0x7c/0x110 [ 80.843250] mei_vsc_hw_start+0x98/0x120 [mei_vsc] [ 80.843270] mei_reset+0x11d/0x420 [mei] The easiest fix would be to just drop the counted-by but with the exception of the ack buffer in vsc_tp_xfer_helper() which only contains enough room for the packet-header, all other uses of vsc_tp_packet always use a buffer of VSC_TP_MAX_XFER_SIZE bytes for the packet. Instead of just dropping the counted-by, split the vsc_tp_packet struct definition into a header and a full-packet definition and use a fixed size buf[] in the packet definition, this way fortify-source buffer overrun checking still works when enabled. | ||||
| CVE-2023-53067 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: LoongArch: Only call get_timer_irq() once in constant_clockevent_init() Under CONFIG_DEBUG_ATOMIC_SLEEP=y and CONFIG_DEBUG_PREEMPT=y, we can see the following messages on LoongArch, this is because using might_sleep() in preemption disable context. [ 0.001127] smp: Bringing up secondary CPUs ... [ 0.001222] Booting CPU#1... [ 0.001244] 64-bit Loongson Processor probed (LA464 Core) [ 0.001247] CPU1 revision is: 0014c012 (Loongson-64bit) [ 0.001250] FPU1 revision is: 00000000 [ 0.001252] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:283 [ 0.001255] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1 [ 0.001257] preempt_count: 1, expected: 0 [ 0.001258] RCU nest depth: 0, expected: 0 [ 0.001259] Preemption disabled at: [ 0.001261] [<9000000000223800>] arch_dup_task_struct+0x20/0x110 [ 0.001272] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.2.0-rc7+ #43 [ 0.001275] Hardware name: Loongson Loongson-3A5000-7A1000-1w-A2101/Loongson-LS3A5000-7A1000-1w-A2101, BIOS vUDK2018-LoongArch-V4.0.05132-beta10 12/13/202 [ 0.001277] Stack : 0072617764726148 0000000000000000 9000000000222f1c 90000001001e0000 [ 0.001286] 90000001001e3be0 90000001001e3be8 0000000000000000 0000000000000000 [ 0.001292] 90000001001e3be8 0000000000000040 90000001001e3cb8 90000001001e3a50 [ 0.001297] 9000000001642000 90000001001e3be8 be694d10ce4139dd 9000000100174500 [ 0.001303] 0000000000000001 0000000000000001 00000000ffffe0a2 0000000000000020 [ 0.001309] 000000000000002f 9000000001354116 00000000056b0000 ffffffffffffffff [ 0.001314] 0000000000000000 0000000000000000 90000000014f6e90 9000000001642000 [ 0.001320] 900000000022b69c 0000000000000001 0000000000000000 9000000001736a90 [ 0.001325] 9000000100038000 0000000000000000 9000000000222f34 0000000000000000 [ 0.001331] 00000000000000b0 0000000000000004 0000000000000000 0000000000070000 [ 0.001337] ... [ 0.001339] Call Trace: [ 0.001342] [<9000000000222f34>] show_stack+0x5c/0x180 [ 0.001346] [<90000000010bdd80>] dump_stack_lvl+0x60/0x88 [ 0.001352] [<9000000000266418>] __might_resched+0x180/0x1cc [ 0.001356] [<90000000010c742c>] mutex_lock+0x20/0x64 [ 0.001359] [<90000000002a8ccc>] irq_find_matching_fwspec+0x48/0x124 [ 0.001364] [<90000000002259c4>] constant_clockevent_init+0x68/0x204 [ 0.001368] [<900000000022acf4>] start_secondary+0x40/0xa8 [ 0.001371] [<90000000010c0124>] smpboot_entry+0x60/0x64 Here are the complete call chains: smpboot_entry() start_secondary() constant_clockevent_init() get_timer_irq() irq_find_matching_fwnode() irq_find_matching_fwspec() mutex_lock() might_sleep() __might_sleep() __might_resched() In order to avoid the above issue, we should break the call chains, using timer_irq_installed variable as check condition to only call get_timer_irq() once in constant_clockevent_init() is a simple and proper way. | ||||
| CVE-2025-58337 | 1 Apache | 2 Doris, Doris Mcp Server | 2025-11-12 | 5.4 Medium |
| An attacker with a valid read-only account can bypass Doris MCP Server’s read-only mode due to improper access control, allowing modifications that should have been prevented by read-only restrictions. Impact: Bypasses read-only mode; attackers with read-only access may perform unauthorized modifications. Recommended action for operators: Upgrade to version 0.6.0 as soon as possible (this release contains the fix). | ||||
| CVE-2023-53074 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix ttm_bo calltrace warning in psp_hw_fini The call trace occurs when the amdgpu is removed after the mode1 reset. During mode1 reset, from suspend to resume, there is no need to reinitialize the ta firmware buffer which caused the bo pin_count increase redundantly. [ 489.885525] Call Trace: [ 489.885525] <TASK> [ 489.885526] amdttm_bo_put+0x34/0x50 [amdttm] [ 489.885529] amdgpu_bo_free_kernel+0xe8/0x130 [amdgpu] [ 489.885620] psp_free_shared_bufs+0xb7/0x150 [amdgpu] [ 489.885720] psp_hw_fini+0xce/0x170 [amdgpu] [ 489.885815] amdgpu_device_fini_hw+0x2ff/0x413 [amdgpu] [ 489.885960] ? blocking_notifier_chain_unregister+0x56/0xb0 [ 489.885962] amdgpu_driver_unload_kms+0x51/0x60 [amdgpu] [ 489.886049] amdgpu_pci_remove+0x5a/0x140 [amdgpu] [ 489.886132] ? __pm_runtime_resume+0x60/0x90 [ 489.886134] pci_device_remove+0x3e/0xb0 [ 489.886135] __device_release_driver+0x1ab/0x2a0 [ 489.886137] driver_detach+0xf3/0x140 [ 489.886138] bus_remove_driver+0x6c/0xf0 [ 489.886140] driver_unregister+0x31/0x60 [ 489.886141] pci_unregister_driver+0x40/0x90 [ 489.886142] amdgpu_exit+0x15/0x451 [amdgpu] | ||||
| CVE-2025-37870 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: prevent hang on link training fail [Why] When link training fails, the phy clock will be disabled. However, in enable_streams, it is assumed that link training succeeded and the mux selects the phy clock, causing a hang when a register write is made. [How] When enable_stream is hit, check if link training failed. If it did, fall back to the ref clock to avoid a hang and keep the system in a recoverable state. | ||||
| CVE-2025-37892 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-11-12 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: mtd: inftlcore: Add error check for inftl_read_oob() In INFTL_findwriteunit(), the return value of inftl_read_oob() need to be checked. A proper implementation can be found in INFTL_deleteblock(). The status will be set as SECTOR_IGNORE to break from the while-loop correctly if the inftl_read_oob() fails. | ||||
| CVE-2025-37867 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Silence oversized kvmalloc() warning syzkaller triggered an oversized kvmalloc() warning. Silence it by adding __GFP_NOWARN. syzkaller log: WARNING: CPU: 7 PID: 518 at mm/util.c:665 __kvmalloc_node_noprof+0x175/0x180 CPU: 7 UID: 0 PID: 518 Comm: c_repro Not tainted 6.11.0-rc6+ #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:__kvmalloc_node_noprof+0x175/0x180 RSP: 0018:ffffc90001e67c10 EFLAGS: 00010246 RAX: 0000000000000100 RBX: 0000000000000400 RCX: ffffffff8149d46b RDX: 0000000000000000 RSI: ffff8881030fae80 RDI: 0000000000000002 RBP: 000000712c800000 R08: 0000000000000100 R09: 0000000000000000 R10: ffffc90001e67c10 R11: 0030ae0601000000 R12: 0000000000000000 R13: 0000000000000000 R14: 00000000ffffffff R15: 0000000000000000 FS: 00007fde79159740(0000) GS:ffff88813bdc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000180 CR3: 0000000105eb4005 CR4: 00000000003706b0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ib_umem_odp_get+0x1f6/0x390 mlx5_ib_reg_user_mr+0x1e8/0x450 ib_uverbs_reg_mr+0x28b/0x440 ib_uverbs_write+0x7d3/0xa30 vfs_write+0x1ac/0x6c0 ksys_write+0x134/0x170 ? __sanitizer_cov_trace_pc+0x1c/0x50 do_syscall_64+0x50/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e | ||||
| CVE-2025-37866 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mlxbf-bootctl: use sysfs_emit_at() in secure_boot_fuse_state_show() A warning is seen when running the latest kernel on a BlueField SOC: [251.512704] ------------[ cut here ]------------ [251.512711] invalid sysfs_emit: buf:0000000003aa32ae [251.512720] WARNING: CPU: 1 PID: 705264 at fs/sysfs/file.c:767 sysfs_emit+0xac/0xc8 The warning is triggered because the mlxbf-bootctl driver invokes "sysfs_emit()" with a buffer pointer that is not aligned to the start of the page. The driver should instead use "sysfs_emit_at()" to support non-zero offsets into the destination buffer. | ||||
| CVE-2025-37863 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ovl: don't allow datadir only In theory overlayfs could support upper layer directly referring to a data layer, but there's no current use case for this. Originally, when data-only layers were introduced, this wasn't allowed, only introduced by the "datadir+" feature, but without actually handling this case, resulting in an Oops. Fix by disallowing datadir without lowerdir. | ||||
| CVE-2025-37875 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: igc: fix PTM cycle trigger logic Writing to clear the PTM status 'valid' bit while the PTM cycle is triggered results in unreliable PTM operation. To fix this, clear the PTM 'trigger' and status after each PTM transaction. The issue can be reproduced with the following: $ sudo phc2sys -R 1000 -O 0 -i tsn0 -m Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to quickly reproduce the issue. PHC2SYS exits with: "ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction fails This patch also fixes a hang in igc_probe() when loading the igc driver in the kdump kernel on systems supporting PTM. The igc driver running in the base kernel enables PTM trigger in igc_probe(). Therefore the driver is always in PTM trigger mode, except in brief periods when manually triggering a PTM cycle. When a crash occurs, the NIC is reset while PTM trigger is enabled. Due to a hardware problem, the NIC is subsequently in a bad busmaster state and doesn't handle register reads/writes. When running igc_probe() in the kdump kernel, the first register access to a NIC register hangs driver probing and ultimately breaks kdump. With this patch, igc has PTM trigger disabled most of the time, and the trigger is only enabled for very brief (10 - 100 us) periods when manually triggering a PTM cycle. Chances that a crash occurs during a PTM trigger are not 0, but extremely reduced. | ||||
| CVE-2023-53042 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Do not set DRR on pipe Commit [WHY] Writing to DRR registers such as OTG_V_TOTAL_MIN on the same frame as a pipe commit can cause underflow. | ||||
| CVE-2023-53036 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix call trace warning and hang when removing amdgpu device On GPUs with RAS enabled, below call trace and hang are observed when shutting down device. v2: use DRM device unplugged flag instead of shutdown flag as the check to prevent memory wipe in shutdown stage. [ +0.000000] RIP: 0010:amdgpu_vram_mgr_fini+0x18d/0x1c0 [amdgpu] [ +0.000001] PKRU: 55555554 [ +0.000001] Call Trace: [ +0.000001] <TASK> [ +0.000002] amdgpu_ttm_fini+0x140/0x1c0 [amdgpu] [ +0.000183] amdgpu_bo_fini+0x27/0xa0 [amdgpu] [ +0.000184] gmc_v11_0_sw_fini+0x2b/0x40 [amdgpu] [ +0.000163] amdgpu_device_fini_sw+0xb6/0x510 [amdgpu] [ +0.000152] amdgpu_driver_release_kms+0x16/0x30 [amdgpu] [ +0.000090] drm_dev_release+0x28/0x50 [drm] [ +0.000016] devm_drm_dev_init_release+0x38/0x60 [drm] [ +0.000011] devm_action_release+0x15/0x20 [ +0.000003] release_nodes+0x40/0xc0 [ +0.000001] devres_release_all+0x9e/0xe0 [ +0.000001] device_unbind_cleanup+0x12/0x80 [ +0.000003] device_release_driver_internal+0xff/0x160 [ +0.000001] driver_detach+0x4a/0x90 [ +0.000001] bus_remove_driver+0x6c/0xf0 [ +0.000001] driver_unregister+0x31/0x50 [ +0.000001] pci_unregister_driver+0x40/0x90 [ +0.000003] amdgpu_exit+0x15/0x120 [amdgpu] | ||||
| CVE-2023-53048 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: fix warning when handle discover_identity message Since both source and sink device can send discover_identity message in PD3, kernel may dump below warning: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 169 at drivers/usb/typec/tcpm/tcpm.c:1446 tcpm_queue_vdm+0xe0/0xf0 Modules linked in: CPU: 0 PID: 169 Comm: 1-0050 Not tainted 6.1.1-00038-g6a3c36cf1da2-dirty #567 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tcpm_queue_vdm+0xe0/0xf0 lr : tcpm_queue_vdm+0x2c/0xf0 sp : ffff80000c19bcd0 x29: ffff80000c19bcd0 x28: 0000000000000001 x27: ffff0000d11c8ab8 x26: ffff0000d11cc000 x25: 0000000000000000 x24: 00000000ff008081 x23: 0000000000000001 x22: 00000000ff00a081 x21: ffff80000c19bdbc x20: 0000000000000000 x19: ffff0000d11c8080 x18: ffffffffffffffff x17: 0000000000000000 x16: 0000000000000000 x15: ffff0000d716f580 x14: 0000000000000001 x13: ffff0000d716f507 x12: 0000000000000001 x11: 0000000000000000 x10: 0000000000000020 x9 : 00000000000ee098 x8 : 00000000ffffffff x7 : 000000000000001c x6 : ffff0000d716f580 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffff80000c19bdbc x1 : 00000000ff00a081 x0 : 0000000000000004 Call trace: tcpm_queue_vdm+0xe0/0xf0 tcpm_pd_rx_handler+0x340/0x1ab0 kthread_worker_fn+0xcc/0x18c kthread+0x10c/0x110 ret_from_fork+0x10/0x20 ---[ end trace 0000000000000000 ]--- Below sequences may trigger this warning: tcpm_send_discover_work(work) tcpm_send_vdm(port, USB_SID_PD, CMD_DISCOVER_IDENT, NULL, 0); tcpm_queue_vdm(port, header, data, count); port->vdm_state = VDM_STATE_READY; vdm_state_machine_work(work); <-- received discover_identity from partner vdm_run_state_machine(port); port->vdm_state = VDM_STATE_SEND_MESSAGE; mod_vdm_delayed_work(port, x); tcpm_pd_rx_handler(work); tcpm_pd_data_request(port, msg); tcpm_handle_vdm_request(port, msg->payload, cnt); tcpm_queue_vdm(port, response[0], &response[1], rlen - 1); --> WARN_ON(port->vdm_state > VDM_STATE_DONE); For this case, the state machine could still send out discover identity message later if we skip current discover_identity message. So we should handle the received message firstly and override the pending discover_identity message without warning in this case. Then, a delayed send_discover work will send discover_identity message again. | ||||
| CVE-2023-53053 | 1 Linux | 2 Linux, Linux Kernel | 2025-11-12 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: erspan: do not use skb_mac_header() in ndo_start_xmit() Drivers should not assume skb_mac_header(skb) == skb->data in their ndo_start_xmit(). Use skb_network_offset() and skb_transport_offset() which better describe what is needed in erspan_fb_xmit() and ip6erspan_tunnel_xmit() syzbot reported: WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 skb_mac_header include/linux/skbuff.h:2873 [inline] WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962 Modules linked in: CPU: 0 PID: 5083 Comm: syz-executor406 Not tainted 6.3.0-rc2-syzkaller-00866-gd4671cb96fa3 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023 RIP: 0010:skb_mac_header include/linux/skbuff.h:2873 [inline] RIP: 0010:ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962 Code: 04 02 41 01 de 84 c0 74 08 3c 03 0f 8e 1c 0a 00 00 45 89 b4 24 c8 00 00 00 c6 85 77 fe ff ff 01 e9 33 e7 ff ff e8 b4 27 a1 f8 <0f> 0b e9 b6 e7 ff ff e8 a8 27 a1 f8 49 8d bf f0 0c 00 00 48 b8 00 RSP: 0018:ffffc90003b2f830 EFLAGS: 00010293 RAX: 0000000000000000 RBX: 000000000000ffff RCX: 0000000000000000 RDX: ffff888021273a80 RSI: ffffffff88e1bd4c RDI: 0000000000000003 RBP: ffffc90003b2f9d8 R08: 0000000000000003 R09: 000000000000ffff R10: 000000000000ffff R11: 0000000000000000 R12: ffff88802b28da00 R13: 00000000000000d0 R14: ffff88807e25b6d0 R15: ffff888023408000 FS: 0000555556a61300(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055e5b11eb6e8 CR3: 0000000027c1b000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __netdev_start_xmit include/linux/netdevice.h:4900 [inline] netdev_start_xmit include/linux/netdevice.h:4914 [inline] __dev_direct_xmit+0x504/0x730 net/core/dev.c:4300 dev_direct_xmit include/linux/netdevice.h:3088 [inline] packet_xmit+0x20a/0x390 net/packet/af_packet.c:285 packet_snd net/packet/af_packet.c:3075 [inline] packet_sendmsg+0x31a0/0x5150 net/packet/af_packet.c:3107 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg+0xde/0x190 net/socket.c:747 __sys_sendto+0x23a/0x340 net/socket.c:2142 __do_sys_sendto net/socket.c:2154 [inline] __se_sys_sendto net/socket.c:2150 [inline] __x64_sys_sendto+0xe1/0x1b0 net/socket.c:2150 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f123aaa1039 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 b1 14 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffc15d12058 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f123aaa1039 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000020000040 R09: 0000000000000014 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f123aa648c0 R13: 431bde82d7b634db R14: 0000000000000000 R15: 0000000000000000 | ||||
| CVE-2019-16256 | 1 Trustedconnectivityalliance | 1 S\@t Browser | 2025-11-12 | 9.8 Critical |
| Some Samsung devices include the SIMalliance Toolbox Browser (aka S@T Browser) on the UICC, which might allow remote attackers to retrieve location and IMEI information, or retrieve other data or execute certain commands, via SIM Toolkit (STK) instructions in an SMS message, aka Simjacker. | ||||
| CVE-2022-49917 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: ipvs: fix WARNING in ip_vs_app_net_cleanup() During the initialization of ip_vs_app_net_init(), if file ip_vs_app fails to be created, the initialization is successful by default. Therefore, the ip_vs_app file doesn't be found during the remove in ip_vs_app_net_cleanup(). It will cause WRNING. The following is the stack information: name 'ip_vs_app' WARNING: CPU: 1 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460 Modules linked in: Workqueue: netns cleanup_net RIP: 0010:remove_proc_entry+0x389/0x460 Call Trace: <TASK> ops_exit_list+0x125/0x170 cleanup_net+0x4ea/0xb00 process_one_work+0x9bf/0x1710 worker_thread+0x665/0x1080 kthread+0x2e4/0x3a0 ret_from_fork+0x1f/0x30 </TASK> | ||||
| CVE-2022-49918 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ipvs: fix WARNING in __ip_vs_cleanup_batch() During the initialization of ip_vs_conn_net_init(), if file ip_vs_conn or ip_vs_conn_sync fails to be created, the initialization is successful by default. Therefore, the ip_vs_conn or ip_vs_conn_sync file doesn't be found during the remove. The following is the stack information: name 'ip_vs_conn_sync' WARNING: CPU: 3 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460 Modules linked in: Workqueue: netns cleanup_net RIP: 0010:remove_proc_entry+0x389/0x460 Call Trace: <TASK> __ip_vs_cleanup_batch+0x7d/0x120 ops_exit_list+0x125/0x170 cleanup_net+0x4ea/0xb00 process_one_work+0x9bf/0x1710 worker_thread+0x665/0x1080 kthread+0x2e4/0x3a0 ret_from_fork+0x1f/0x30 </TASK> | ||||
| CVE-2022-49903 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-11-11 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ipv6: fix WARNING in ip6_route_net_exit_late() During the initialization of ip6_route_net_init_late(), if file ipv6_route or rt6_stats fails to be created, the initialization is successful by default. Therefore, the ipv6_route or rt6_stats file doesn't be found during the remove in ip6_route_net_exit_late(). It will cause WRNING. The following is the stack information: name 'rt6_stats' WARNING: CPU: 0 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460 Modules linked in: Workqueue: netns cleanup_net RIP: 0010:remove_proc_entry+0x389/0x460 PKRU: 55555554 Call Trace: <TASK> ops_exit_list+0xb0/0x170 cleanup_net+0x4ea/0xb00 process_one_work+0x9bf/0x1710 worker_thread+0x665/0x1080 kthread+0x2e4/0x3a0 ret_from_fork+0x1f/0x30 </TASK> | ||||